× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for June 9, 2010
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2001 Chrysler Sebring LXi 2.7L Timing VIN: 4C3AG52H61
My question is this, before I pull the timing chain cover off and recheck timing marks to see if it jumped when priming. Is it possible that the flex plate/tone wheel may be installed incorrect? Or are the bolt holes off set so that the plate will only go back...
View
2002 Chrysler Sebring LXi 2.7L No Start VIN: 1C3EL55R22
Recently the primary timing chain tensioner went bad on my wife's 2002 Sebring Convertible 2.7L and caused the chain to jump bending all 12 intake valves. So I pulled the heads, sent them to the machine shop. Now I have the car back together with 3 new chains,...
View
2004 Chrysler Pacifica 3.5L Hesitation VIN: 2C8GF68474
Hello all, i am scratching my head on this one. I have a code p0016 cam and crank out of sync. If you rev the engine it starts to bounce like it is hitting a rev limiter. It idles perfect and without a load it goes around the lot no problem. As soon as you dr... Trouble codes: P0016
View
2005 Chrysler Pacifica Touring 3.5L Timing Belt VIN: 2C8GF68405
I'm puting this car back together after it came in with a broken T- Belt. Had to do head work , bent 18 valves Well, I down to putin the T-belt on and the timing marks are not lineing up. I can get the crank and the the left cam right on But the Right ( Rear )...
View
2000 Dodge Neon ES 2.0L No Start VIN: 1B3ES46C1Y
Hellow I have a problem neon here . The car cranks but no start. i have no ign coil drivers on crank . can actuate the drives with drb3 and get a fliker . or unplug the cam sensor and get it to start . I have hard wire the cam sensor to the pcm due to the fact...
View
2001 Dodge Durango 4.7L Misfire, MIL Lamp on VIN: 1B4HS28N31
to all dodge pros. got this durango that has codes:- p0356 & p0306. have switched s/plug, coil, injector and no transfer of code to the switched cylinder. good compression and fuel pressure. what am i missing. thanks everybody in advavce
View
2003 Dodge Ram 2500 5.7L Cuts out, Stall VIN: 3D7KU28D23
This thing is a real headache. The customer says after about 35+ miles it will go to running real bad and loses power and eventually stall. After the stall the truck will not start till the next day. I have put over 70 miles on this truck and have had no probl... Trouble codes: P0171 (Lean Bank 1)
View
1991 Jeep Cherokee 4.0L Brake lights/Hazardlights inopertive VIN: 1J4FJ8754M
I have a 1991 Jeep Cherokee that the brake lights and harzard lights does not work but the turn signals do work. I replaced the turn signal switch and brake light switch still either one works.There's no power at the brake light switch, I check alldata for wir...
View
1999 Jeep Cherokee SE 4.0L Poor Idle Quality, Hesitation, Surge VIN: 1J4FT68S7X
This jeep runs very rough while idling until vehichle is warmed up.when it reaches 210 its like flipping a switch and its fine. If you try to drive it before it warms up it acts like low fuel pressure, bucking and hesitating, but drove with a guage and is fine...
View
2002 Jeep Liberty Sport 3.7L Engine VIN: 1J4G448K9W
Hello, I am helping a friend at another shop here in town. he has swaped a 2006 3.7l engine in to his 2002 jeep liberty, using the 2002 harness, transmission and sensors etc. Of corse it will not start and sets a hard Cam sensor code as well as a Crank sensor...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
1997 Dodge Ram 1500 Laramie 5.2L Charging VIN: 1B7HC13Y3V
Thanks for all the quick responses. After multiple hours of searching, finally found the wiring harness connector at the driver side hood hinge hade bad connection. There is 3 connectors together mounted to the fire wall. After disconnecting and cleaning pins ...
13
1998 Dodge Ram 1500 Laramie 5.9L Fuel in oil? VIN: 1B7HF16Z7W
Hey Guys, Sorry for the delay but I've been waiting to see if what I did actually had any effect on the problem. I had all the injectors out before I posted and couldn't see a leak. So I stuck paper towels under them and left them out over the weekend. On ...
18
2003 Jeep Grand Cherokee Overland 4.7L recirculation door motor VIN: 1J8GW68J73
Thanks guys, had to pull the dash to replace the recirc. motor Got it out and found the cam that connects it to the door was split. Checked the door operation while I was there and it was free. Put everything back together and retested, noise was gone.
7
2005 Other Chrysler knight 300CID tach VIN: 1RF4245456
hello all, repsitioned all wiring, rechecked everything i could think of, looks like its a bad signal out of the ecm to tach but unfortunatly customer picked up going on trip, so when i get it back and fixed i will let all of you now whats happening thanks.
4
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next