Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for January 25, 2010
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1998 Chrysler Cirrus LXi 2.5L Hesitation VIN: 1C3EJ56H4W
When Arrived, SES Light On With Misfire Codes P0301,P0302. Replace Cap & Rotor First Because Cyl. 1&2 Are Next To Each Other In The Cap. Seemed Better But Would Still Misfire Sometimes. Sprayed Water Near Cyl. 1&2 And Would Then Really Misfire So Changed Plugs...
2000 Chrysler Sebring JX 2.5L Stall VIN: 3C3EL45H6Y
Hi Guys, Thanks in advance for any replies. I have a 2000 Sebring Convertible here with a 2.5L V6 that has an intermittent stall at idle condition. I verified it at my house, this is a friend's car that I agreed to take into work with me this last Friday. It w...
2000 Chrysler Town & Country (Van) LXi 3.8L key in chime VIN: 1C4GP54L2Y
Thank You for taking a look see,the problem I'm having is the chime is sounding even when the key is out.This does'nt sound like "rocket science" but it's turned out that way.Is it me or a bad switch from Chrysler? As usual the information systems or should I ...
2001 Chrysler Sebring LXi 2.7L MIL Lamp on VIN: 1C3EL56U91
car pass the emission test. Failed cause trouble codes. Run perfect at idle and cruising (idle 750 rpm) no vacuum leaks found, no exhaust leaks found,the freeze frame is at idle, oxygen sensors upstream cycling good, downstream O2 sensors steady between 900 t ... Trouble codes: P0172, P0175
2006 Chrysler 300 (Car) Limited 3.5L shifting VIN: 2C3KA53G86
this limo had a rear replaced about 2 weeks ago. the car was running fine for several days (to our knowledge). it was then sent for a detailing. before it got there it went into limp. we scanned car and got code p0731- gear ratio error in 1st. we cleared code,...
2000 Dodge Ram 1500 Truck 3.9L burned ecm VIN: 1B7HC16X5Y
I have no idea where to start on this one. The dark green/orange wire from the ASD realy which powers up the injectors, O2 heaters, and some trans stuff also goes to the PCM as "ASD sense", and it has burned the pin completely off the PCM at this connection, p...
2007 Dodge Durango SLT 4.7L fuel leak VIN: 1D8HB48P87
I am new to this evap system, use to LDP type. The customer states the he fills his truck with fuel and fuel comes back up the filler neck and leaves a spot on the ground the size of a basketball intermitantly. He said he is filling on level ground and at vari...
2007 Dodge Sprinter 2500 3.0L glow plugs VIN: WDOPE74577
This sprinter had a code P0672 for the #2 glow plug and I can not find any info on just what the lay out of cylinders is on this V6 Diesel! My biggest question is where are the cylinders on this engine? 123 on the one side and 456 on the other or is it 135 and...
2008 Dodge Avenger SE 2.4L MIL Lamp on VIN: 1BLC46K78N
This car has never acted up on me but customer said that is intermittant. The electronic acelerator pedal lite flashes and loss of power and rough running happens. The one thing I saw was the APP voltages are different from APP1 and APP2. At idle App1 is .855v... Trouble codes: 2101 (Electronic thorrotle control motor performance), 2110 (Electronic thorrrottle control forced limited rpm), 2112 (Electronic thorr control unable to open)
1996 Jeep Cherokee SE 4.0L Excessive Emissions, MIL Lamp on VIN: 1J4FJ28SXT
Vehicle brought into shop with check engine light on , found o2 sensor no voltage. replaced o2 sensor everything worked fine for about 15 minutes. o2 sensor voltage with koeo reads 0.00 volts, if you watch scan data for about 5 minutes voltage will eventuall... Trouble codes: P0171 (fuel system lean), P0133 (upstream o2 slow response), P0131 (upstream o2 shorted to ground)

Fixes & Summaries for Chrysler
Fix/Summary Answers
2005 Chrysler Pacifica Limited 3.5L MIL Lamp on VIN: 2C4GF68485
Thanks too all who responded. I had installed Bosch O2 sensors. I for know have replaced the downstream sensor with an OE Chrysler sensor and the problem hasn't reoccured. Thanks again, Randy. Trouble codes: P2097 (Downstream fuel system rich 1/2).
1998 Dodge Ram 1500 Truck 5.2L 2-3 shift VIN: 1B7HF13YXW
rechecked the fluid condition, then spoke to customer he changed the fluid prior to bringing me the vehicle, it is badly burnt guess it was flushed out on the road test. Thanks to all on this one. The governor pressure never goes above 65 psi. Reverse feels...
2001 Dodge Ram 1500 Truck 5.2L No Start VIN: 3B7HC13Y91
well, with no other obviouse reason, im going with pure gut instinct. Im replacing the dist/oil pump drive shaft. When trying to remove from engine, i had to hammer it out. The drive gear appears to be pressed onto drive shaft, if siezeing in block, or trying ...
2004 Dodge Ram 2500 Truck SLT 5.7L Hesitation, Stall VIN: 3D7KU28D44
i will say it is fixed. found 2 things. a coil connection not fully seated and the trans filter had fallen from its seat. so far have not heard from customer.
2004 Dodge Ram 2500 Truck SLT 5.7L anti-theft VIN: 1D7K428034
Well, I managed to delete 2 of the three replys somehow- but the concensus was front control module, along with the tidbit to look for aftermarket devices wired into the DLC. Customer came in to chat with me today and told me his drag team mechanic son has "lo...
2004 Dodge Ram 2500 Truck SLT 5.9L Electronic VIN: 3D7KU28C84
govenor pressure/temp sensor repaired problem. thanks for all the help. mel
2006 Dodge Charger 2.7L wont shift VIN: 2B3KA43G46
After several replies of the pcm/tcm being the same module, and a few replies that it was covered under manufacturers warranty, I sent the car to the dealer(who told me it wasn't covered- at first- but a phone call to Chrysler changed that). They changed out t... Trouble codes: U0101 (lost communication with TCM), P0605 (internal control module ROM error).
1996 Jeep Grand Cherokee Laredo 4.0L Surge, Cuts out, Stall VIN: 1J4GZ58S7T
Well I got the ecu back today and I installed it along with a coil, although the coil ohmed out ok I did notice the it was slightly melted, I do not know what caused this. The Vehicle runs great again, how long I don't know. I tried to research what the CKP ...
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next