|Prev||Professional Automotive Repair Technical Discussions for December 28, 2009
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|1998 Chrysler Sebring JXi 2.5L Poor Idle Quality, Stall, Misfire, MIL Lamp on VIN: 3C3EL55H3W
I was given car after Apprentice Tech did a Tuneup ( plugs and wires) to fix a misfire. Car has been here two weeks. I initially checked fuel pressure and found no problem it was when I tested and founf that the coil could not produce enough spark to jump a HE... Trouble codes: P0306 (Miisfire cyl 6), P0301 (Misfire cyl 1), P0302 (Misfire cyl 2), P0303 (Misfire cyl 3), P0304 (Misfire cyl 4), P0305 (Misfire cyl 5)
|1992 Dodge Dakota 3.9L starter VIN: 1B7GG23X3N
This truck came in as a no crank no start. after testing i found the starter circuit working up to a 2 wire connector located right behind the battery. i found when cranking there is a full 12v at the male end. i used a jumper wire at the female end and found ...
|1994 Dodge Ram 2500 Truck 5.9L No Start, Hesitation, Cuts out, Stall VIN: 1B7KF26Z7R
Vehicle came in with a crank/no start problem. Fuel pressure at 40psi. Has spark and injector pulse. Truck will start when carb cleaner or either is sprayed down the throttle body. After that truck will start no problem, unless it sits on a cold soak. All pids...
|2006 Dodge Durango SLT 4.7L first gear VIN: 1D4HB58N86
2006 Dodge Durango with 45RFE/545RFE trans came in with check trans. feels like no first gear.. codes p0700 transmission control system p0750 LR solenoid circuit I'm pretty sure that the P0700 code is set whenever there is an internal transmission problem. I...
|2006 Dodge Durango SLT 4.7L MIL Lamp on, trans VIN: 1D4HB58N86
2006 Dodge Durango with 45RFE/545RFE trans came in with check trans. feels like no first gear.. codes p0700 transmission control system p0750 LR solenoid circuit I'm pretty sure that the P0700 code is set whenever there is an internal transmission problem. I... Trouble codes: P0700, P0750
|2000 Jeep Grand Cherokee Laredo 4.0L No Start, Cuts out, Stall VIN: 1J4GW48S0Y
Road tested after replacement of spark plugs - no more misfire cold & hot. Upon de accel (about 8MPH), snuffed out - no warning. Restarted, got to shop, died again. Each time this happens now it is HOT only (runs NICE! cold). We replace crank sensor (OE) right...
Fixes & Summaries for Chrysler
|2004 Chrysler Sebring Limited 3.0L left side VIN: 4C3AG52H14
Though the vehicle isn't correctly repaired, it has heat again. The problem has been confirmed as no/low flow to the heater core. We disassembled the H2O manifold at the rear of the engine (along with most of the cooling sys) to find no visible problems other ...
|2005 Chrysler Town & Country (Van) LX 3.3L tail lamp VIN: 2C4GP44RO5
thank you for the replies. some said there would be screws near the lamp. others said there would be push pins. the vehicle was equipped with the push pins. being unfamiliar with these fasteners i thought they were bump stops for the liftgate. i did try to rem...
|2007 Chrysler sprinter 3.0L swirl valves VIN: WDPPF34597
Well I wanted to give this one time before I closed it... I found that the bank with the code had worn out linkage causing the metal part of the linkage to not make contact with the sensor when its at the fully closed position like it should... Also make sure ...
|1991 Dodge Stealth R/T 3.0L Hesitation, Low Power VIN: JB3XD64B0M
Rechecking our diagnosis, we found that the the rear bank, front cam was 1 tooth off. Intially we felt the coarse timing marks would not allow the cam to be exact but reset anyway. Power characteristics were restored.
|2007 Jeep Grand Cherokee Laredo 3.7L No Start, trans temp light on VIN: 1J8GR48K47
Well, I tested and wiggled all wiring, found bad temp sensor. Temp would change when moving shifter from D to R. Put in new valve body, comes with all the sensors and prdl attached. very easy to do. all seems well now. Thanks to everyone for the help. On the o...