Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for November 16, 2009
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1995 Chrysler LeBaron GTC 3.0L 3-4 shift VIN: 1C3EV4536F
found to not shift up on road test no matter how fast you go, trans fluid looks good. has power and grounds to pcm. scanner shows to stay in n and not shift at all on road test in in garage. possable direction in can go in diag im not sure. is it normal for th...
View
2001 Chrysler Concorde LXi 3.2L Poor Idle Quality, Hesitation, Cuts out, Misfire VIN: 2C3HD36J71
Customer called and asked for price on catalytic converter. I asked why and she replied that it glows red. I told her that i didn't think it was a cat but we would have to check it out. The car was towed in and we proceded to check it out and found that someon...
View
2004 Chrysler Pacifica 3.5L shift indicator VIN: 2C8GF68464
This Pacifica came in with the shift indicators not lit properly on the dash in some gears and a P0706 which is a code for transmission range rationality. When it was in in park and sometimes in other gears as well it would light up all the indicators for the ...
View
2000 Dodge Neon High Line 2.0L Hesitation VIN: 1P3ES46C4Y
I've got a good one here,this Neon has a temperature guage that reads low,ect sensor show around 100* on scan tool, but engine is running around 195 like it should,voltage at sensor is 1.4 volts lower than voltage reading on scan tool,also noticed same conditi...
View
2002 Dodge Grand Caravan ES 3.8L Electronic VIN: 2B8GP74L62
Vehicle came in with the complaint that the blowers were only working in high. vehicle is equipped with front and rear AC. Has two seperate relays and two seperate resistors. Both front and rear will only work in high. Checked the connections to the control he...
View
2003 Dodge Ram 1500 Truck 4.7L Axle Shaft-Ft. Drive VIN: 1D7HU118N8
Vehicle came to my shop=complaint of clicking noise made worse while in 4-wheel drive. short road test confirmed inner C/V joint on drivers side wobbling bad. R&R C/V shaft=found short drive shaft spline worn down half way caused by worn C/V joint. Factory man...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2004 Chrysler Pacifica 3.5L Starting VIN: 2C8GM68494
wow! I love iatn. so while waiting for posts we saw that there is technically no nuetral safety switch but the ecm does comm. prndl through. when that ground is bad it will not comm. with ecm. so off of all your suggestions it was that ground at the trans ...
7
1998 Dodge B1500 3.9L Rear lights VIN: 2B7HB11X1W
Every one said it was a ground problem. I starting to doubt this after checking what I thought were all the grounds. It so happened that both rear light sockets were defective and not allowing both brake and running light circuits to pass through the ground ci...
8
2002 Jeep Liberty Sport 3.7L VIN: 1J4GL58K72
took others advice and removed pan to check if filter was clogged, found bent support bar for two pistons on side of valve body and one of the pistons was 3/4 the way out. bought updated bar and used piston with new seals, re-assembed and drove.
4
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next