 Prev |
Professional Automotive Repair Technical Discussions for May 20, 2009 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2001 Chrysler PT Cruiser 2.4L Excessive Emissions, Ltft -13 VIN: 3C8FY4BBX1 we employ the ph2 solutions program,and while doing drive cycle,o2 and evap monitors wont run,analysis states rich condition pending wich is a condition that will turn on the mil light.it hasnt yet.ltfi is at -13 and it occurs as soon as purge flows.i have dis... Trouble codes: P0172 |
View | |
| 1992 Dodge D150 5.2L No Start, Stall VIN: 1B7HE16Y1N Hello everyone, have one kicking my but, obviously. This dodge truck came in with customer stating start and stall after about 30 min. They drove it in, I go out try to start and it does not. Had 2 second relay with good pressure, but would drop right off. No ... |
View | |
| 1998 Dodge Ram 1500 Laramie 5.2L 3-4 shift lock up VIN: 3B7HF13Y6W transmission would go in and out of overdrive/lockup with out warning, it will also hunt for the correct gear when you take your foot off the gas and reaccelerate. on my solus i can watch the od and lock up solenoid being commanded on and off when the problem ... |
View | |
| 1999 Dodge Ram 1500 Van 5.9L Started motor VIN: 2B6HB11YSX this van came in on the hook with a no start. We found that a fuse in the relay box under the hood was blown and replaced it and it worked for a couple months. It came back and we had put a starter in it because after we hammered on it, it stopped blowing the ... |
View | |
| 2003 Dodge Dakota SLT 3.9L no cruise control VIN: 1D7HL48N03 thanks in advance for any help on this basket case! this truck came in with a non-op speed control, auto I.D. on scanner showed veh. to be a 2002 so i figured it had a used PCM and later found it to have a 3.9L insead of the 4.7L that it came with. so i contin... |
View | |
| 2003 Dodge Ram 2500 Van 5.2L Stall VIN: 2D7JB21Y03 This car will start and run, then stall, or equally will not start at all. When this happens, there is no spark or fuel injection signal. There is constant fuel pressure when this behavior occurs. There are no codes stored, and no CEL. So far the ASD relay and... |
View | |
| 2003 Dodge Ram 1500 SLT 5.7L Hesitation VIN: 1D7HA18D23 has anyone seen failures on the app sensors several.alll the dealers seem to stock them,but the sell rate on them is not very high.t-body wass pretty expensive but like i said got rid of those codes and in the learn part of the relearn it learns the tps but no... Trouble codes: P2115 (app seneor wont learn), P2116 (app wont learn), P2166 (app sensor wont learn), P2167 (app wont learn) |
View | |
| 2004 Dodge Ram 1500 ST 5.7L MIL Lamp on VIN: 11D7HA16D8 I need some Chrysler Evap schooling today. This vehicle a week ago had a P0441 stored. I replaced the purge solenoid and NVLD pump for good measure. This has cured my problems in the past. It came back 3 days ago with a P0443 stored(evap purge circuit problem)... Trouble codes: P0441 (Evap. Purge system performance) |
View | |
| 2004 Dodge Ram 1500 ST 5.7L rear tail lights VIN: 1D7HU16D14 i have an 04 dodge ram 1500 the rear brake lights are always on when you turn on the key. the 3rd brake is not on, only when you press the brake. all the other lights work fine, any help would be nice thanks |
View | |
| 2007 Dodge Ram 2500 SLT 5.9L abs module VIN: 3D7KS29C07 Problem is check engine light & abs light are on all the time, along with the speedometer not working. I have engine computer code U1412-implauisble speed single(comes from abs module) Abs module code C1079 tone wheel teeth count performance. In abs computer s... |
View | |
| 1997 Jeep Grand Cherokee Limited 5.2L Excessive Emissions VIN: 1J4GZ78Y9V No other codes fuel tirm ok no sign of running lean or coolant leaks or running rich. O2 start switching at same speed at cruise. Useing after market direct fix cat. Trouble codes: P0420 |
View | |
| 2003 Jeep Liberty Sport 3.7L BCM and fuse box VIN: 1J4GL48KX3 Hi to all. We are working on a 2003 Jeep Liberty, It came to us with electrical problems. We found the BCM was melted and the fuse box to which the BCM attaches to is also melted. They are both cooked to the point where it looked like they could have caught o... |
View | |
| 2007 Jeep Grand Cherokee Laredo 3.7L Surge VIN: 1J8GR48K67 Jeep guys: I'm trying to help and restore confidence in our customer. She drives everyday 40+ miles each way. On 1 trip, at aprox 25 mph, when foot taken off throttle, car wanted to accelerate, then came down, did no want to accel when requested. Check engine ... Trouble codes: P00, P00, P00 |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2001 Chrysler 300M 3.5L Blower motor VIN: 2C3AE66G91 I have to close this help request due to time restraints but first I would like to thank the three that responded. The customer is a elderly man that has a limited income, and must wait till the first of the month to recive his money, by that time this help re... |
4 | |
| 2002 Dodge Intrepid SE 2.7L cruise VIN: 2B3HD46R62 Sorry bout the delay. Found in the diagnostic routine to test for servo power from PCM engine must be running. We did replace the PCM so when cruies was engaged at least the indacator would now stay on all the time but the cruise still did not operate. check r... |
2 | |
| 1999 Jeep Cherokee Sport 4.0L oil pressure VIN: 1J4FF68SXX As several suggested I removed the pan one more time to recheck what my tech has said he checked. I rechecked the main bearing clearance slightly over .002", rod bearings were the same. A closer look at the cam indicates this maybe the area causing the conce... |
8 | |
| 2005 Jeep Grand Cherokee Limited 5.7L Check gas cap light VIN: 1J4HR58295 Thanks for the info all, the day after I posted this the light went out and did not return, When the light was on the only way I was able to clear it was to disconnect the battery, when I did the memory resets with the scanner it would still be on. When/if the... |
9 |
