 Prev |
Professional Automotive Repair Technical Discussions for December 2, 2008 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1997 Dodge Ram 2500 5.9L Mechanical VIN: 1B7KF2672V hey guys the mechanic at the shop of the customer has put alot of new parts on this truck. I have cheked all of his work for possible problems. Any way the truck will only idle very poorly and as soon as you touch the gas pedle it dies. the ex. smells very rit... |
View | |
| 2002 Dodge Stratus R/T 3.0L Poor Idle Quality, Stall VIN: 4B3AG52HX2 Hi all and thanks for the help. This Stratus came in with a "will not idle complaint." This was true, if you did not hold the throttle open, the car would start and die. I checked for codes, there were none. I removed and ohmed the old IAC and found a problem.... |
View | |
| 2002 Dodge Neon SE 2.0L tcm VIN: 1B3ES46C82 Problem with TCM, sent to the Dealer to see if they could reprogram it or it had to be replaced. Dealer stated that with the internal error, it would have to be replaced. Asked if they could program another used TCM, dealer stated no, it already had a VIN in i... |
View | |
| 2003 Dodge Caravan SE 2.4L MIL Lamp on VIN: 1D4GP25B13 customer came in with cel light on. code p0440. i checked and found 0 tsb's. so i went ahead and checked the evap system for leaks. i used a redline smoke machine. pressure stabilized and found no leaks. im not sure what could the problems be. ive seen ldp's (... Trouble codes: P0440 (evaporative system leak) |
View | |
| 2003 Dodge Sprinter 3500 2.7L No Start VIN: WD2YD54233 This unit is a non starter unless given a shot of ether then fires instantly and runs well until its shut down then a no start either hot or cold. Since many hands had been in it we revised the past RO's and info the customer paid for at other shops as a precu... |
View | |
| 2002 Jeep Grand Cherokee Laredo 4.0L blend door actuator VIN: 1J4GW48S62 I've tested the key on power input...fine The ground is good..even an extra one is run The temp control input responds normal from the control head (varying voltage when I change knob position) snipped 4th wire as instructed by autoline..(doesn't seem to go... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1994 Dodge Ram 1500 5.2L Surge VIN: 1B7HC16Y7R Thank you for responding to my request I did receive various replies that could help, however I had done most of the things already. Replies ranged from checking the TPS and ECT and looking for intake vacuum leaks and checking to make sure the EGR valve is sea... |
5 | |
| 1994 Dodge B350 5.2L backfire VIN: 2B7JB31Y4R this van I inherit from customer i buy all injectors install & no change still misfires i had an instructor from standar came in to help he spend some 3 hours with me going over everything i done looking at data he also agreed that is not mechanical failure b... |
27 | |
| 1994 Dodge Ram 1500 5.2L Cuts out, Stall, MIL Lamp on VIN: 3B7HF16YXR thanks to all that replied.after checking connections and monitering sensors i decided to take advice from Ed in pennsylvania and try heat gun to computer,didnt help.at this point i heated each sensor individually until it started and ran without condition(cra... Trouble codes: 21 (o2s signal not switching), 31 (purge solenoid circut open or short), 24 (tps voltage higher than max limit). |
3 | |
| 2001 Dodge Stratus SE 2.4L Rear disk VIN: 1B3EJ46X71 There was a lot of help from everyone. How I found the fix was to take the brakes apart one peice at a time. When I took out one of the caliper mounting bolts from either side the wheels spun free. I replace the slide pins,bolts and rubber bushings. When I too... |
14 | |
| 2003 Jeep Liberty Renegade 3.7L 4x4 VIN: 1J4GL38K93 It actually was the switch in the top of the transfer case. There were no problems with the wiring and this is a basic completely manual system, no modules or programming involved. Thomas from New York was the first to reply with a very good description of the... |
3 |
