Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for November 10, 2008
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2005 Chrysler Town & Country (Van) Limited 3.8L door locks VIN: 2C8GP64L25
NO power door lock function, bcm code set for left side door lock output failure, cleared code and resets instantly, following flow chart for this code it has you check resistance in the left door lock output and the left sliding output ckt to groung out of co...
View
1999 Dodge Dakota 3.9L Mechanical VIN: 1B7GL22X7X
vehicle driven in with erractic oil pressure. customer stated that oil pressure dropped to zero, lifters were tapping, he drove home about 3 miles that way. after restarted later oil pressure seemed ok and noise went away. he then drove and oil pressure now go...
View
1997 Jeep Grand Cherokee Laredo 4.0L Cuts out VIN: 1J4GZ58SXV
start and idle car,it may run for two hours or two minutes engine dies and starts right back.i have verified no fire once when it did not start right away,but now it may run all afternoon,scan tool shows everything in normal ranges,one thing it will throw 4 co... Trouble codes: P0351
View
1999 Jeep Grand Cherokee Limited 4.7L azc module VIN: IJ4GW66N2X
vehicle has duel zone auto hvac system. everything works fine but azc module input power harnees overheats only when blower is set to high speed then system shuts off. when it cools down, system will run fine and will continue to run fine as [...] as you don't ...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
1992 Dodge W250 5.9L crankshaft seal VIN: 3B7KM23C4N
the kit from cummins was very complete and simple once the advise from the iatn members showed me the way. the small white plastic ring was used to guide the seal onto the crank without damage, then the large white ring was used to evenly hammer the seal flush...
6
2000 Dodge Grand Caravan SE 3.3L Hesitation, Surge, Cuts out VIN: 1B46P44G1Y
Thank you all for the help. We checked all sensors that controlled air\fuel ratios with no change. One other observation is that the timing advance pid drops to zero when the surge or cut out occurs. The customer declined further diagnosis at this time. Again ...
13
2001 Dodge Ram 2500 Truck 5.9L No Start VIN: 3B7KF23601
vehicle ended up being the injection pump thanks to all that replied very helpful information.
3
2007 Dodge Ram 3500 Truck ST 5.9L speedo VIN: 3D7MX48CX7
THANKS TO AL [...] FOR THE REPLIES. IN ADDITION TO THE ORIGINAL POST,I REPLACED THE TRANS SPEED SENSOR HOPING FOR A LITTLE LUCK. THATS WHEN I DECIDED TO ASK FOR HELP. AFTER REVIEWING THE REPLIES, AND DOUBLE CHECKING THE WIRING FOR THE WHEEL SPEED SENSORS, I CALLED ...
5
1990 Jeep Wrangler Sahara 4.2L No Start, Poor Idle Quality, Misfire VIN: 2J4FY49T8L
Had to take a break from jeep for sanity purposes. I read all posts. Still have problem.Timing is set properly and carb adjusted correctly. When I start jeep o2 voltage is at .o42.As jeep warms up o2 stedily increases until rich at .848 at idle not changing. A...
8
2002 Jeep Grand Cherokee Limited 4.0L Misfire VIN: 4M2Z486K22
I lab scoped the cam and crank sensors which were good. Performed a current ramp with lab scope of the fuel pump and was a good pattern. Ckd for distributor gear being worn and was good. O2 sensors tested good. At this point the customer is not willing to d...
11
1998 Plymouth Voyager 3.0L MIL Lamp on, shift indicater out VIN: 2P4FP2536W
well we finaly fixed this van, found a wrong heater controle head was installed from previous shop. It appears that all the ccd+buss are tied togeather & the incompatible controle head caused the shorting problem. thanks for all the help Terry Trouble codes: P1695.
3
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next