|Prev||Professional Automotive Repair Technical Discussions for November 6, 2008
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|2005 Chrysler 300 (Car) Limited 3.5L instrument cluster VIN: 2C3JA53G25
cluster's mph is at 0 mph and doesn't move. the odometer works and is digital on the cluster, my scanners datastream shows that the input and output speed sensors are working and even shows odometer reading, but thats all. car is out of warranty and customer ...
|1996 Dodge Stratus ES 2.5L No Start VIN: 1B3EG56H4T
will start every time after changing dist. will run for 45-minutes, after it dies no inj pulse no fire . sometimes after it cools off it will start . Scaner that we have availble is a Modis and Gensis
|1996 Dodge Ram 1500 Truck 5.2L abs light on VIN: 3B7HC13Z8T
HI Y'ALL! I have this Dodge Ram 1500 pu with REAR ABS ONLY that the abs light stays on. It flashes code 4 when checking at 16 pin connector. I have 5 v ref to the rear abs valve (below master cyl). I tried to unplug module under dash and could not clear codes....
|1998 Dodge Grand Caravan SE 3.3L Excessive Emissions, Stall, Poor Fuel Economy VIN: 1B4GP44G4W
hello all,thanks in advance for taking the time to read my post. This caravan runs extremly rich, plugs are black after a week,removed injector rail no leaking injectors I'm leaning towards pcm. Modis scanner data stream shows inj pw at 2.5ms koer at 205 farhe...
|2002 Dodge Ram 1500 Truck 5.9L running lights only VIN: 1D7HU1872J
thanks to all for the kind answers ahead of time. I have a 02 dodge pickup came in with no running lights. headlights, turn signal, fog lamps, dash, interior lights . All that works but the running lights front and rear dont work. Been pulling hair. Need help.
Fixes & Summaries for Chrysler
|1999 Chrysler Town & Country (Van) LXi 3.8L brakes VIN: 1C4GP54LOX
Thanks much too all that responded,we sure appriceate it !!! Vehicle has an extended filler neck @ brake fluid res.,were NOT able to initally sample brake fluid.During fault tracing found brake hyd system contaminated (customer suspects unhappy ex spouse rel...
|1996 Dodge Grand Caravan SE 3.3L Hesitation, Cuts out, MIL Lamp on VIN: 1B4GP44R4T
Thanks to all who replied to this problem.I replaced the tps with a factory one,and the problem seams to be fixed. Customer has not reported any more problems.I guess in the future I'll be using OE parts rather than aftermarket. Thanks again to all who respone... Trouble codes: 24 (tps voltage low).
|2002 Dodge Neon ES 2.0L MIL Lamp on, SPEEDOMETER NOWORK VIN: 1C3ES46C62
thanks you guys you try to help me. most people says out put sensor or wires which i was agree because there was no snapon scanner was not reading out put signal. on guy said cluster i was not agree. i replaced it doesn't work. the customer refuse the further ... Trouble codes: P0500 (novehicle speed sensor signal).
|2003 Dodge Ram 1500 Truck 4.7L Stall, MIL Lamp on VIN: 1D7HA18N53
Thanks again IATN techs. Gilbert and Glen [...] believe were right in that these cam and crank sensor codes are one trip codes. If the light is not on, then there is no problem. What I was seeing on the Genisys was the crank sensor not in sync when cranking and th... Trouble codes: P0335, P0340.
|2004 Dodge Ram 2500 Truck ST 5.9L cruise VIN: 3D7KU28C04
I guess that I am the first to encounter the "BRAKE RAT" denied for cruise control operation parameter. No information was given and I have not been able to repair this cruise. the "PARK ALARM" function is due to a recall because of vehicles not being fully i...
|1995 Jeep Grand Cherokee Laredo 5.2L Cuts out, Misfire VIN: 1J4GZ58Y7S
well guys you hit it on the nail aftermarket ecms a junk after 9 days of tracing and back probing and 5 different ecms 2 used 6 aftermarket and one oe part all problems are gone no miss starts fine and customer is happy its bad when you cant rule out new parts...