 Prev |
Professional Automotive Repair Technical Discussions for October 6, 2008 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1994 Chrysler Concorde 3.3L blend door VIN: 1C3JK54L1R First of all excuse the incorrect VIN, posting from home. I know I have a blend door problem, has no heat, and sets blend door codes during self test, also never gets warm during self test. I was starting to pull the blend door motor and customer had to get go... |
View | |
| 1973 Dodge dart 225CID No Start VIN: LL41C3R167 Hoping to get some help on this dodge ,has no spark from coil customer came in battrey will drain in few days,but vehicle decided not to start for us.positive wire on coil disconected has 12 v/conected has 6.5v.balast has 12 v on 3 conectors and 6.5 on one.dis... |
View | |
| 2005 Dodge Ram 1500 ST 5.7L Surge VIN: 1D7HU18D35 Vehicle has a surge with a very light throttle. I can feel it in low right before it shifts. It is predominantly felt at 25mph.. Vehicle surges sometimes as much as 400 RPM.. I have scanned the computer and found no codes.. When it is surging the Data shows th... |
View | |
| 2005 Dodge Ram 3500 ST 5.9L flywheel VIN: 3D7MX48CX6 replacing the clutch assy. customer supplied all parts. removed transmission, six speed with dual mass clutch. down to the flywheel assy and can find no info on how to get to the bolts that bolt to crankshaft. never ran into this application before. anybody ou... |
View | |
| 1987 Jeep Cherokee 4.0L Differential VIN: JCMR7845HT After the repair of the rear drive-shaft, the owner reported that he was having intermittent transmission problems. He was also experiencing increasing noise and vibration from the front of the vehicle. He wanted the front drive-shaft removed to check the U-jo... |
View | |
| 1997 Jeep Grand Cherokee Laredo 4.0L Cuts out, Stall VIN: 1J4FX58S3V The vehicle cam in for an intermittent stall/cut-out and check engine light, P-0351, ignition coil primary circuit. It was at another shop, they did the full tune-up, cam sensor and ignition coil, they gave up on it, and she brought it to me. I noticed that wh... Trouble codes: P0351 |
View | |
| 2001 Jeep Wrangler Sport 4.0L alternator VIN: 1J4FA49581 Hello all, I believe that I am overlooking something simple. The charging system is inop on this 01 wrangler. I have done that basic visual inspection, followed the chrysler pinpoint tests, and have Load tested the generator control circuit wires with a headla... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1994 Dodge Caravan SE 3.3L Hesitation, Surge, Cuts out, Stall VIN: 2B4GHY5R7R Well I finally figured it out, out of desperation I removed the under hood fuse relay centre , checked all connectors to fuses and relays,OK, Next I started to check the harness between fuse box and harness, no faults. Removed coil pack for access to wiring h... |
20 | |
| 1998 Dodge Grand Caravan 3.3L Wipers VIN: 284GP44R7W thank you all for the immediate help. the problem turned out to be the BCM. My customer was not interested in spending any money on this old van so i removed the wire going from the bcm that feeds the wiper on/off relay and put a toggle switch to ground. the ... |
11 | |
| 2000 Dodge Grand Caravan Sport 3.8L 4 wheel ABS VIN: 1B4GT44L2Y Well I have finally repaired this vehicle using a "preowned" Hydraulic control unit. I was squeemish at the thought myself but once installed it bled like a dream without a scan tool in under 3 minutes! It was instantly evident that this corrected the air en... |
12 | |
| 2001 Dodge Caravan SE 3.3L clock, radio VIN: 1B4GP25301 Thanks for the replies. Customer put an aftermarket radio in the van and all is well. Thanks again for the help. |
4 | |
| 2002 Dodge Intrepid SE 2.7L transmission VIN: 2B3HD46R52 Thanks for the advice guys. We replaced the solenoid block and tightened pins at btrans harness connector. Problem solved. Thanks again! Howard |
6 |
