 Prev |
Professional Automotive Repair Technical Discussions for July 25, 2008 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2003 Chrysler Town & Country Limited 3.8L exterior turn indicators VIN: 2C8GP64LX3 Good Morning Techs, Posting this for a fellow tech. This van does not have external turn indicators, i.e. turn signals or hazards do not flash outside the van. The indicators on the dash do work and there is an audible "clicking" from the electronic relay. Rep... |
View | |
| 1989 Dodge Dakota 3.9L 4-3 down shift VIN: 1B7GL26X7K After replacing shift solenoid we now have 1st 2nd 3rd and OD under 25mph full throtle will cause down shift to 1st. or 2nd. after 25 mph it stays in OD even at full throtle. This is fine untill he needs the power on hills or to pass. What are we missing?? |
View | |
| 2002 Dodge Dakota 3.9L Backfiring VIN: 1B7GL12X92 Customer came in concerned about backfiring, rough running and tune up needed. Ended up doing intake manifold gasket, full tune up(spark plugs, wires, dist cap and rotor), alternator belt, thermostat, coolant flush,and fuel injector cleaning. Upon taking home... |
View | |
| 2002 Dodge Ram 2500 Van 5.2L loss of pedal VIN: 2B7JB221Y7 Hello all! Customer had this van towed in after experiencing a loss of pedal, and stated that the right front wheel was "smoking". A visual inspection found no apparant faults...brake fluid level OK, nothing broken or missing, no leakage anywhere. While the A... |
View | |
| 2002 Dodge Ram 1500 SLT 4.7L Cuts out, Stall, Misfire, MIL Lamp on VIN: 3D7HA18N12 This truck was brought to me by a Dealer I used to work for. They replaced the 4.7 liter engine due to overheating damage with a O.E. reman. Now the engine starts, runs good for a few seconds and stalls. If you provide throttle assist it will stay running albe... |
View | |
| 2002 Dodge Ram 1500 SLT 4.7L Engine VIN: 1D7HU18N72 replaced head gaskets. once we got this truck back together #3 cylinder is misfiring, injector would not fire so we replaced injector and now fuel and spark both are okay. still misfiring. only 30lbs of compression on that cylinder added atf and compression hi... |
View | |
| 2005 Dodge Sprinter 2500 2.7L No Start VIN: WD2PD74455 When you try to start the van a message comes up on the dash START ERROR The key tab also does not lock or unlock the doors The batt.'s in the key tab they are asking me to check the SKREEM DTC'S but my computer will not tell me what the SKEEM stands for. I ha... Trouble codes: P1630 (Immoblized), P2152 (Starter relay ckt short to ground), P1615 (ECM voltage low) |
View | |
| 2002 Jeep Grand Cherokee Overland 4.7L compressor? VIN: 1J8GW68J22 charged system with 27 oz 134 pressures are as stated recovered freon and removed expansion valve no blockage found blew air through evaporator core, condenser and receiver dryer no restrictions or blockages found please help thanks mark |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1994 Dodge Ram 2500 5.9L No Start VIN: 1B7KC26C4R I am going to call this one fixed. Apparently the vehicle sits for weeks at a time and the problem has only happened once since the customer had the fuel hoses replaced. From the many replies I received hose leaks are the most common problem, but injectors hav... |
10 | |
| 1998 Dodge Intrepid ES 3.2L No Start, Cuts out, Stall, MIL Lamp on VIN: 2B3HD56J0W thank you to all that helped me as this was my first time posting for help but this beast is fixed i was able to find a way to run a self test on the cluster ended up replaceing the pcm now gauges work great thank you again Trouble codes: P1698, P1695, P1687. |
10 | |
| 1995 Plymouth Voyager 3.3L serpentine belt VIN: 2P4GH2533S this is fixed, went to dealer and ordered pulley kit. all it is is a larger depressed washer that goes on the front of the tensioner pulley to keep the belt from walking off. put new tensioner and washer on and everything is fine now. thanks to all who replied... |
23 |
