|
|
1998 Dodge Pickup 5.9L No Start
ORIGINAL-Crank and no start,turn off ignition switch and
retry,then engine starts/runs/no smoke.This happens every
time hot or cold. We are loosing voltage to lift pump and
wait to start lamp. Replaced ignition switch.Inspected
wires to connections. Tested lif... |
View |
|
1998 Dodge Caravan 2.4L blower motor
this one has me really stumped as i cant find much in shop
key on the air bag and sbec [...] no number to go with
them. i listed all complaints as i am thinking thay all may
be related.these problems are intermitants so i need to
make it break to get anywh... |
View |
|
1996 Jeep Cherokee 4.0L Poor Idle Quality, Misfire
customer has constantly complained of engine miss at idle.
it is noticeable but very minor and not completely
consistent. we have replaced the 02 sensor (it was bad),
the harmonic balancer (just a guess), the distributor (the
shaft was loose)and we even discon... |
View |
|
2000 Jeep Grand Cherokee 4.0L Hesitation, Cuts out, Stall, MIL Lamp on
hello and T.G.I.F. this vehicle intermittently dies at idle
and cuts out under acceleration with no codes at that
time.repaced crank sensor and vehicle was hard to
start,and/or no srart at times,and ran very rough,with
codes now setting [po320 no crank ref. si... Trouble codes: 320 (no crank ref. sig. at pcm), 1391 (intermittent loss of cmp or ckp). |
View |
|
1999 Plymouth Breeze 2.4L Poor Idle Quality, Stall, Misfire
Car came in for timingbelt replacement.Had engine light on
and a code for EGR.Car ran and idled decent.Replaced
belt,now car runs like crap.Check datastream and found all
cyliders missfiring.Took off belt and tried to realign
marks following step by step sever... |
View |
|
1991 Chrysler New Yorker Fifth Avenue 3.3L door locks
Never did get these automatic power locks disabled. As I mentioned, I could go into the BCM with my Snap-On MT2500 and turn the locks off but as soon as you exit the program, it returns the module to it's normal state which is having the locks enabled. Perhaps... |
4 |
|
1999 Chrysler Sebring 2.5L Cuts out
thanx for all the replies, all were helpful . i replaced the crank sensor and the problem hasnt reoccured in 2 weeks of driving. the customer will bring it back for the timing belt service if no further problems. thanx again for the help!!! |
6 |
|
2002 Chrysler Town & Country 3.8L LR Wheel Speed Circuit
Well, It turns out that I got another bad CAB from the dealer. New CAB solved the problem. |
6 |
|
1998 Dodge Pickup 5.9L hub assy
SORRY FOLKS I JUMPED THE GUN ON THIS ONE. THE CUSTOMER CALLED ME IN A HUFF AND SAID THE BEARING IS OUT AGAIN, BUT WHEN THE TRUCK GOT HERE THE LEFT WHEEL BEARING IS OK BUT THE FRONT PADS ARE INTO THE ROTORS AND THE RIGHT FRONT WHEEL IS OUT OF BALANCE 12 OZS!!!... |
16 |
|
2000 Dodge Intrepid 2.7L upshift
I thank all of the people who responded ,using every ones ideas
led us back to the TCM. not having a good scanner and not being able to reprogram TCM,s, we sent them to someone who could.
the TCM was replaced , the customer is back on the road and happy.
than... |
7 |
|
2004 Dodge Intrepid 2.7L MIL Lamp on
Thanks for all the help guys, after fabricating a vacuum source to the fuel filler neck and determined the NVLD was not working per the test test by one of the members. I replaced the NVLD. Immediatly after I installed the plug connector on the new part, I hum... Trouble codes: P0441 (Evap Purge System Preformance). |
6 |
|
2007 Dodge Pickup 5.7L starter/ignition
I replaced the TIPMCGW. Still no crank. This one was sent to the dealer. They have replaced the TIPMCGW again. They replaced another part they did not name, and they are replacing the starter. I still don't know what has or will fix this truck. |
3 |
|
Prev
