× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for December 28, 2007
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Ford
Help Request Answers
1995 Ford Mustang 3.8L MIL Lamp on VIN: 1FALP4047S
ok guys, this is a good one. 95 mustang from another shop. they replaced o2 sensors for a lean code. they used bosch sensors. b2s1 and b2s2. they are both switching properly. (they later found a plugged air filter that was probably the cause of the lean codes)... Trouble codes: P0175
1998 Ford Explorer Eddie Bauer 4.0L camshaft chain VIN: 1FMZU34E8W
Left side(driver's side)camshaft chain broke at one link. All chains,cassettes and tensioners were replaced 2800 miles ago.After inspecting then replacing broken chain there is a grinding rubbing noise,front engine area,most noticable at front cover area.
1998 Ford Expedition Eddie Bauer 4.6L Suspension, Drivetrain VIN: 1FMRU18W2W
The vehicle has a vibration between 30-50 mph. Feels like a out of balance driveline. I'm aware of the TSB calling for replacement of both drivelines. To be sure, I installed both front and rear drivelines from a known good vehicle. No change. U-joints are ok....
1999 Ford F-250 Super Duty Lariat 5.4L trans slipping VIN: 1FTNF21L7X
Truck was towed in as a no start, found that there was no power to the s terminal of the starter. Replaced the gear selector switch truck starts and runs. Now the customer says the transmission is slipping. No check engine lights are on. First could this be tr...
2000 Ford F-350 Super Duty XL 7.3L No Start VIN: 1FTXSX30F4
hello,---diesels arent our everyday vehicles we see-but it is a commercial account of ours-it was towed in as a no start- it sounds like its trying to start but doesnt-could this code p1670-effect its starting-or do i need to look elsewhere-and if so wheres a ... Trouble codes: P1670 (ef feedback signal injector driver module fault)
2002 Ford Expedition XLT 5.4L convertor VIN: IFMEU15L02
this one has me stumped. vehicle came in with overdrive light flashing and check engine light on and poor idle. When put into drive vehicle would die. Ran DTC codes are p0741 and p1744 which are both tcc system perofrmace/stuck codes. We replaced torque conver...
2004 Ford F-350 Super Duty XL 6.0L Hesitation VIN: 1FTSW31PX4
this thing when cold has no power will not go, after a couple of minutes takes off and runs great all day, when it does this almost feels like it misses or has a cylinder detonating, no codes and data on scan tool looks ok, believe may have a injector issue do...
2004 Ford E-350 Super Duty 6.0L No Start VIN: 1FDSS34P54
Thanks in advance. We removed engine for head gasket replacement, they were blown, The vehicle had had a code for #2 injector for a while and we installed new injectors on one bank. Reinstalled engine and the high pressure oil system will not climb above 350 p...
1999 Mercury Cougar 2.5L Booster/master cylinder VIN: 1ZWFT61L3X
Greetings Ford Techs. This Couger came to us with all 4 brakes smoking hot and we determined that the Master cylinder wasn't releasing fluid pressure to any of the wheels. The customer had previously replaced the master cylinder [Ford part] for this exact caus...

Fixes & Summaries for Ford
Fix/Summary Answers
2004 Ford Freestar SEL 4.2L no gears VIN: 2FMZA52244
THANKS EVERYONE for the replies! You hit the nail on the head. The spline were striped in the torque converter. I did'nt thing to check the line pressure before I posted the problem would have show up with that test. We installed a new converter, flushed it an...
1999 Mercury Mystique LS 2.5L MIL Lamp on VIN: 3MEFM66L0X
Thanks to everyone! Everyone said something different, the manuels all say something different, The Ford dealer said 35-45 psi, I'm going with that. Thanks, Tim
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next