
![]() |
Professional Automotive Repair Technical Discussions for September 18, 2007 International Automotive Technicians' Network (iATN) - Members Only |
Next ![]() |
(Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. |
Open Help Requests for Chrysler
Help Request | Answers | |
1998 Chrysler Cirrus LXi 2.5L dist. VIN: 1C3EJ56H1W came in a week ago crank no start tested dist and hade no signal out of the dist. replaced it and was no help also changed cranksensor it failed 1 out of 3 tests still did not help checked wires to pcm and all tested good asd relay is shuting down after 2 sec ... |
View | |
2003 Chrysler Town & Country Limited 3.8L blower motor VIN: 2C8GP64L83 lights on the cd player constintly flash,blower motoer runs on high at all times |
View | |
1995 Dodge Ram 1500 5.2L No Start, Cuts out, Stall, Misfire VIN: 1B7HF16Y2S This Truck Is Giving Me A Headache. It May Go For A Few Miles Or A Few Feet But Quits. Sometimes It May Start, Sometimes Not. No Matter What Has Been Done The Issue Remains The Same. First A CKP From Aftermarket. It Rubbed On Flywheel (Seemed To Be Made Wrong)... |
View | |
2002 Dodge Ram 1500 SLT 5.9L 1-2 shift, range slection, rev limiter VIN: 1D7HU18Z12 The truck feels like it has a delayed shift between 1 and 2 gear. While driving, the gear position on our scan tool bounces all over the place from 4th to invalid to 2nd to park without any rhyme or reason. Also if you push the throttle to the floor it feels l... |
View | |
2004 Dodge Intrepid SE 2.7L pump VIN: 2C3HH46R24 I have an Intrepid with a noisey power steering pump most of the time. Sometimes it's quiet. I have already replaced the pump(NAPA) and pressure hose(Chrysler). I have flushed the system and filled it with ATF +4 from Chrysler. The pump sounds like it is full ... |
View | |
2006 Dodge Ram 3500 SLT 5.9L Shifting out of Park position VIN: 3D7LX38C46 Customers complaint when she is parked in a flat surface she has a hard time to shift out of park position, and when she does a clunking noise is heard/felt. All the rest of the positions she has no problem. To me it kind of sound like when some one parks on a... |
View | |
1996 Eagle Vision ESi 3.5L Poor Idle Quality, Cuts out, Misfire VIN: 1G3W2E4465 Since the fuel pump and filter were replaced the vehicle had a rough idle,I cleaned the injectors,replaced the plugs and wires,drained and refilled the tank,ran the injector balance test,compression,rechecked the fuel pressure (48 psi),checked spark and scanne... Trouble codes: 403 (egr) |
View | |
1985 Jeep Grand Wagoneer 5.9L Cuts out, Stall VIN: 1JCNJ15N2F I am at my wits end on this one. The vehicle would occasionally stall with customer. After it had cooled down it would start right up and run fine. I checked the carbeurator and the fuel lines after I finally got it to stall with me and they would actually be ... |
View | |
2002 Jeep Grand Cherokee Limited 4.7L crank sensor VIN: 1J4GW58N93 this vehicle came towed in with no start condition and code po320 inspected and found no sign from crank sensor to pcm and no signal to asd relay from pcm so replaced crank sensor and pcm and recieved sign to asd relay and vehicle started but with rough idle a... |
View |
Fixes & Summaries for Chrysler
Fix/Summary | Answers | |
1984 Dodge D150 5.2L Timing VIN: 1B7GD14T3E I pluged the vacuum line into the carb and checked the timing at idle it was at 12 and at 2000 rpm it went to 20 Thanks for all the help |
12 | |
1994 Dodge Ram 2500 5.9L engine control fuse VIN: 1B7KC26C7R thanks guys for the great information you offered it was all good stuff. unfortunatly the problem is to intermittant to prove any of these suggestions. customer decided to wait for the problem to progress rather than through any more money at it. thanks again ... |
4 | |
1997 Dodge Caravan 2.4L Cuts out VIN: 2B4FP25B7V Thanks for the help. I had already checked the fuel pressure during failure... it's okay. Checked all the grounds and wiring. After eliminating all other possibilities we replaced the PCM and that did it. My techs are always ready to throw a PCM at a problem, ... Trouble codes: P0132 (O2 sensor voltage high B1S1). |
3 | |
1997 Dodge Stratus 2.4L Poor Idle Quality VIN: 1B3J46X1VN Thank you for your replies and sorry it took me so long to post the fix. Customer finally brought it back to inspect timing belt. It was off a tooth on the exh cam. Three out of six of your replies suspected this was the case. Replaced the belt, reset KAM, run... |
6 | |
1998 Dodge Caravan 3.0L Poor Idle Quality, Hesitation, Surge, Cuts out, Stall, MIL Lamp on VIN: 2B4GP2535W Thanks to all that responded. This vehicle did indeed have a cracked flex plate. If you remove the inspection plate (hard job - dang motor mount), you can easily see the cracks and the fact that it has moved. Pulled trans, changed flex plate, re-assembled, ... Trouble codes: P1391 (Loss of Cam or Crank Signal). |
4 | |
2003 Dodge Ram 1500 SLT 4.7L Ride VIN: 1DLHU18N23 Thank you to the 7 who replied. I did install the Monroe Reflex shock absorbers at all 4 corners, made a huge difference.Customer is very happy. I did a thorough check of the front end, found that the upper control arms and lower ball joints had been replaced ... |
7 | |
1995 Jeep Cherokee Sport 4.0L Air Bag VIN: 1J4FJ68S2S Way over thunk this setup, the screw itself is adjustment by its length. Back it off till its stops turn it in till bottoms.The screw tip goes in a plastic housing at rear of assembly with spring loaded lever for dissarm witch was blown apart. Thanks Guys for ... |
3 | |
1998 Jeep Cherokee Classic 4.0L a/c airflow VIN: 1J4FJ68S0W Since I have posted, the customer has not had a problem with the a/c . However we have had cooler weather since then. I am sorry I don't have any other useful info. If I see car agian for that I will post an update Thabk You, Bob [...], Coon Rapids Service Inc... |
8 | |
2002 Jeep Grand Cherokee Overland 4.7L auto climent control VIN: 1J8GW68J22 The fix for this vehicle was to cut and splice in the new connectors. Thanks to all that replyed that removing the dash to replace the entire harness was not nessary. |
10 |