 Prev |
Professional Automotive Repair Technical Discussions for July 6, 2007 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1995 Chrysler Cirrus LX 2.5L No A/C Clutch Engaugement VIN: 1C3EJ56H2S This Cirrus 2.5L has no a/c compressor clutch engaugement. I switched the relay with the fuel pump, but no luck. With my MODIS I can get the clutch to come on with key on engine off. My Modis shows the pressure transducer at 3028 Kpa. I translate this to 438 P... |
View | |
| 1996 Chrysler Sebring JXi 2.5L No Start, Stall VIN: 3C3EL55H5T quite going down road, no start let set for hour will restart. |
View | |
| 1999 Chrysler Town & Country LX 3.3L alarm set VIN: 1C4GP54GXX hello, I am hopeing a chrysler tech can tell me whats up with this van. It was hit in front(air bags did not deploy). Was repaired and all was good. Did not have a key fob for it but the alarm could be set by locking the doors and all was well. Then few months... |
View | |
| 2003 Chrysler PT Cruiser GT 2.4L MIL Lamp on VIN: 328FY78G33 rad fan works can use scan tool to turn fan on dont see any problem took car to dealer had ecm reprogramed on the way back lite came on code p0480 fan module next? Trouble codes: P0480 |
View | |
| 1999 Dodge Grand Caravan SE 3.3L Excessive Emissions, Poor Idle Quality, Hesitation, Surge, Cuts out, Stall, Poor Fuel Economy VIN: 2B4GP44G9X The upstream O2 trace is almost flatlined on the rich side 1.0V, and will fault to Open Loop sometimes or may just report as Closed Loop. LTFT & STFT are maxed out at -25% and yet no Check Engine Light (on dash and scan tool). I replaced the Upstream O2 Sensor... |
View | |
| 2001 Dodge Grand Caravan Sport 3.3L limp in mode VIN: 2B4GP44R61 CEL on DTC 1768,(relay output always off) followed Mitchell flow chart, replaced TCM and still have limp in mode to 2nd, with DTC 1768. After changing TCM we performed the pinion factor proceedure, then went on to shift quick learn. It would not perform the qu... |
View | |
| 2004 Dodge Ram 1500 ST 4.7L speedo VIN: 1D7HU18N44 Hello all im Rob the new service manager at All Things Automotive in Fort Collins Colorado I have not figured out how to change the name and stuff from the old guy but will I'm working on a 2004 Dodge Ram 1500 4.7 and have a speedo that bounces and sometimes d... |
View | |
| 1989 Jeep Cherokee 4.0L tailshaft bushing Greetings, gang; Two pleas for sources, please... 1) The Jeep is a 2WD with the AW40, and the tailshaft bushing is gone. MerChryco says 400+ mangoes for a new tail housing; I'll scrap it first. Any body got a source on bushings, or fix kits, or exchange reb... |
View | |
| 2003 Jeep Grand Cherokee Laredo 4.0L No Start, Cuts out VIN: 1J4GW48S43 The Jeep came in on a tow truck cause it died on the road. When it arrived, it would crank and not start. After sitting for an hour or so, it started. It ran for a few minutes and died. It would start right back up and run for a few minutes and die. I had a fu... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1992 Dodge Colt 1.5L No Start VIN: JB3CUZ4A9N This is the first car that I've ever had to give up on, but I've done everything I know to do. I got a few good replies, and I went over and over the wiring diagrams that I have but I never got it fixed. The MPI control relay is good, and I'm getting B+ at ECU... |
6 | |
| 1997 Dodge Intrepid 3.3L climate control & power windows & door locks VIN: 2B3HD46T4V thanks to all who replied! the customer travels and when he comes back he agrees to replace the ignition switch - the information that i received is the fix - almost 14 replies all telling me to replace the ignition switch - thanks fellow techs - keep fixing c... |
15 | |
| 1999 Dodge Ram 3500 5.9L fuel leak VIN: 1B7MC3369X Well, there is no quick answer. No one else seems to have had this problem. I guess we just had some not so good OEM parts. What I did to eliminate any further comebacks was to split the solid steel line and put a piece of high quality rubber hose in the middl... |
9 |
