Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for June 4, 2007
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1991 Chrysler Imperial 3.3L shifting VIN: 1C3XV56L1N
this is for all the electrical gurus, thanks in advance. we have a 91 chrysler imperial, low mileage,very nice. the lady let it over heat and blew the head gaskets, melted 2 pistons, we rebuilt the engine , new radiator, hoses , etc. now the transmission only ...
View
1997 Chrysler Sebring JX 2.5L Poor Idle Quality, Cuts out, Stall VIN: 3C3EL45H7V
Vehicle came in not running. Had new parts installed elswhere. We replaced crank sensor. Vehicle runs but very badly. Will lose injection pulse and get very weak sprk but vehicle will continue to idle (very bad) Also will lose cam and crank sync. Cam and crank...
View
1998 Chrysler Cirrus LXi 2.5L Brake shoes VIN: 1C3EJ56H1W
Replaced rear brake shoes/drums and wheel cylinders after the left rear wore out from holding on/overheating in Aug/06. It happened a 2nd time, 1 month later and we replaced the cylinder and shoes on that side again. A few weeks after that the same problem ret...
View
2002 Chrysler Sebring GTC 2.7L bcm VIN: 1C3EL75R12
This car came in 2 weeks ago with low r134 and leaking evap core. We orderd core from aftermarket suplier and came in wrong. We then oredered OEM from Dodge and installed. I recharged the a/c and road tested the car. A/c was blowing 39 degrees. Called customer...
View
2004 Chrysler Sebring Limited 3.0L Hard start VIN: 4C3AG52H54
Hello and thank you Customer states that after the car sits for ten hours or more, he then has to pump the brakes to get it to start. I told him that pumping the brakes would not have anything to do with starting the engine. It is just taking a long time crank... Trouble codes: P335
View
1997 Dodge Dakota 5.2L steering VIN: 2BEHD56DY0
Customer has had ongoing intermittent problem with power assist. The truck will loose power assist and require excessive force to rotate steering wheel. It began occuring last year. We replaced the rack and pinion, flushed the lines and replaced the p/s pump. ...
View
2000 Dodge Intrepid 2.7L MIL Lamp on VIN: 2B3HD46R8Y
Hello everyone, I can't really give you much more info. than this the customer ran vehicle out of oil and set motor up.We had a engine rebuilder remove ,rebuild and install motor now we have a ses light on with [fd undocumented code present],any help would be ... Trouble codes: FD
View
2000 Dodge Intrepid 2.7L abs VIN: 2B3HD46R6Y
The yellow ABS & red brake lights are on. This vehicle is not equiped with ABS. There is a jundtion block were the abs module would be. No trouble codes stored in any module. Parking brake switch released. Master cylinder full of fluid, & low brake fluid senso...
View
2002 Dodge Caravan SE 2.4L Misfire, MIL Lamp on VIN: 1B4GP25B32
Came in with crank sensor code, ignition coil #2 primary circuit (PO352), and idle speed control motor code. Fixed crank sensor code with new crank sensor, fixed idle speed motor with computer, replaced coil, plugs & wires, ran good for two days but never clea... Trouble codes: P0352
View
2003 Dodge Ram 2500 Truck 5.9L No Start VIN: 3D7KU28623
This truck came in with a no start, only starts with either hot or cold. After vehicle is started with either it runs great lots of power no misfire or stumble. No codes. Fuel pressure 0lbs KOEO, about 800lbs cranking. Don't know much about Diesel engines any ...
View
2002 Jeep Grand Cherokee Limited 4.7L No Start, Cuts out VIN: 1J4GW58N72
the ads fuses blows slow the first time i test drove after putt in the fuese it ran ok after replaceing coils that it ran BAD Trouble codes: P0320 (no crank reference), P0340 (no cam signal at pcm), P1299 (vacumm leak found / iac-fully seated), P1389 (no asd relay output voltage at pcm)
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2003 Chrysler Intrepid 3.5L trans shifting VIN: 283HD56G03
The car appears to be fixed,we replaced the solonoid pack and also the fluid and filter.We also checked the solonid valve for sticking or binding, is was fine.This solved the po1776 code which re-appeared on a regular basis.It has been a couple of weeks now an...
10
1999 Dodge Grand Caravan SE 3.3L Inst. cluster VIN: 2B4GP24GX1
Problem tuned out to be broken wire (power feed) from fuse box to inst. cluster. repaired wire and all systems work fine. thanks to everyone!!
6
1999 Dodge Ram 1500 Truck 5.2L pinion bearing
Thanks everybody for all the responses! I ended up borrowing the spreader tool and everything worked out fine. I guess you really do need the right tool for the job-jd
16
2003 Dodge Neon SXT 2.0L charge light VIN: 1B3ES56C93
Thanks for the help! Three people hit it on the head with the batt temp sensor. We found the connection bad sensor at the sensor. Thanks again for the help Duane
4
2003 Dodge Ram 1500 Truck 4.7L Shift interlock VIN: 1D7HU16NX3
First of all thanks for all who replied. After testing all the electrical systems tied into the shifter interlock and trailer brake wiring (all tested fine) I decided to change the cable. Only available OEM, the solonoid is attached and fairly easy to replace ...
4
1998 Jeep Wrangler Sport 4.0L Poor Idle Quality, Hesitation, Misfire VIN: 1J4FY1953W
The fix for this vehicle was to replace both of the oxygen sensors. After driving through multiple warm-up periods the problem has disappered completly. Many thanks to all who responded.
9
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next