Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for May 17, 2007
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1995 Chrysler Town & Country (Van) 3.8L convertor VIN: 1C4GH54L2S
Hi group, This is my own personal vehicle I keep for a spare. I don't get very much involved with transmissions but I am trying to save some money due to the age of van. It has a terrible chatter or shudder at times when driving over 30 mph. It comes and goes ...
View
2000 Chrysler Voyager 3.0L convertor
noise coming from bellhousing area. in drive warm engine at idle. non rytmatic, sounds like belt noise but from bellhousing area. removed tran and checked flex plate and convertor bushing, gose away when put back in park.
View
2003 Chrysler PT Cruiser GT 2.4L MIL Lamp on VIN: 3C4FY78G83
Hey guys, Here's this weeks headache. We have this vehicle towed in for a engine crank/no start complaint. Our customer allready pulled a code Po335-crankshaft sensor circuit error. We found the sensor plastic body to be loose when attempting to perform a sig...
View
1994 Dodge Ram 2500 Truck 5.9L Hesitation, Surge, Cuts out, Poor Fuel Economy
Thanks in advance for any help you folks can supply me on this truck. The first time I worked on this vehice the customer stated that at times it would surge and buck to the point that he thought it was going to quit on him, but it never has. I could not verif... Trouble codes: 51 (system lean)
View
1998 Dodge Ram 2500 Truck 8.0L left rear axle VIN: 3B7KF26W5W
remove the bolts holding axle to hub and axle will not come out. wasn't aware of any clips holding axle in but removed rear cover to be sure. there wasn't. has anybody had any problem with getting axles out? thanks
View
2000 Dodge Dakota SLT 4.7L mill light on VIN: 1B7GL2AN8Y
hey every one we are need of some serious help. as the topic states we have a 2000 doge dakota here that keeps on bringing up a engine code (p0204)(inj/4 control circuit fires inproperly) SNAP-ON MT 2500 and after clearing code 10 secs later light re appers...
View
2000 Dodge Ram 2500 Truck 8.0L engine VIN: 1B7KF23W7W
vehicle came in for transmission rebuild,rebuilt trans ,cutstomer drove home two days later is back in shop drives fine for two to five minutes then stalls constantly and some times will not restart for 30 seconds check engine light flashes,but no codes scanne...
View
2004 Dodge Ram 1500 Truck ST 4.7L delay wiper VIN: 1D7HU18N94
wipers work properly in low and high settings, but will not work in delay setting, when i turn the setting from low to delay while engine is running they keep operating at low speed. with key on engine off the wiper will work in delay mode - sometimes, but as ...
View
1993 Jeep Grand Cherokee Limited 5.2L Blower Fan, etc VIN: 1J4GZ78Y8P
Automatic temp control unit not functioning. Have tried known good unit and swapped into other Jeeps and all work ok (blower fan, resistor, control module all good!) Unit powers up, display comes on, but no control of fan or blend motors, etc. I do not have ...
View
1998 Jeep Wrangler SE 2.5L MIL Lamp on VIN: 1J4FY29P2W
hello everybody.I need some advice on how to proceed with this lovely jeep tj.The customer has gone to the dealer with this for the passed 3 months.What the jeep does is flash the mil light on when ever it feels like it,sometimes comes on when starting,sometim... Trouble codes: P1391
View
1998 Jeep Wrangler SE 2.5L Hesitation VIN: 1J4FY29PXW
Hello All; I sure hope someone can help me out. This is my own truck. When the truck is started cold, it will idle at around 2200 rpm, the idle will eventually slow to normal. Also I have noticed a cold hesitation that was not present prior to the fast idle. ...
View
2004 Jeep Grand Cherokee Laredo 4.7L drivetrain VIN: 1J4GW48N04
hello all having a hard time finding a noise in this 04 grand cherokee it is a knocking noise in the front of the vehicle goes away on a left hand turn, sometimes on a right hand turn i thought it was in the front differential but got it in the air and hear no...
View
1992 Plymouth Voyager LE 3.3L No Start VIN: 2P4GH55R6N
this van came to us from another shop for no start. the customer had a engine installed. no spark or injector pulse. we have replaced the cam and crank sensor. we now have spark, but only on #2 and #5 cylinders. we checked cam timing and found to be off (2) te...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
1993 Dodge Shadow 2.5L Poor Idle Quality, Surge, Stall VIN: 1B3AP24K7R
THANKYOU(THANKYOU(THANKYOU) The ultimate problem was the pickup coil in the distributor. I should have gone with my instincts and replaced it, as I was leaning that way. Also wire wiggle test should have told me also. However, after I had exposed the wiring ha... Trouble codes: 51 (O2 sensor lean).
10
1996 Dodge Neon 2.0L starting VIN: 1P3ES47C5T
thanks for all responses after fixing trans and got car running i replaced the alt and all is good i guess the alt case ground was open letting power through my ground bad news is the moter the costomer supplied has a blown head gasket
6
2001 Jeep Cherokee Classic 4.0L suspension ,body VIN: 1J4FT58SX1
My main quetion is still unsolved , does a rear axle on a 2wd 8.25 have some up and down clearance between the axle shaft and the axle bearing. i tried new axles and bearings and i get the same clearance . the problem appears to be solved by removing the kyb g...
8
1998 Plymouth Grand Voyager Expresso 3.3L brunt clutchs VIN: 2P4GP44R8W
Thank you to every one how took the time to help me. Yes, when you work on a car like this there is always going to be problems. I looked into replacing the Trany be for starting. It was not in the bedget. I know that I was going to be pulling more than on...
11
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next