 Prev |
Professional Automotive Repair Technical Discussions for October 2, 2005 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for All Makes and Models
| Help Request | Answers | |
| 2001 Acura Integra LS 1.8L MIL Lamp on VIN: JH4DC4378Y This vehicle came in with a rattling convertor about 8 months ago and was replaced with a aftermarket cat.The vehicle was run through an analysis and was running fine.A few months later the vehicle returned with a check engine light on and code po420. The deal... Trouble codes: 420 (Cat Detereation) |
View | |
| 1997 Acura Integra LS 1.8L ecu VIN: DC1-120218 hello everybody, i have a curly one. this honda integra came to us with 3 fault codes for the ABS one code was for the control monitoring circuit (low fluid handbrake applied etc) we replaced the disc pads and raised the fluid level which cleared the code. the... |
View | |
| 2005 Hyundai Santro 1000CC Hesitation VIN: PKOO247895 Hi all members of iATN The problem is very difficult, please reply urgently. Problem is The vehicle comes in workshop for While accelerating, the vehicle HESITATES and even JERKS. I will cleaning the throttle body, T.P sensor, iACvalve, and also checks all ... |
View | |
| 1998 Isuzu Rodeo LS 3.2L Surge VIN: 42S2CK58W4 Got the truck back a week ago w egr & vss codes. Repl those sensors,cleared codes & reset monitors. Now the truck is back with same codes & surge complaint. When you drive with scantool VSS ON SCANNER GOES CRAZY SOMETIMES WHILE THE SPEEDO IS CORRECT??? We have... |
View | |
| 1992 Pontiac Grand Prix SE 3.1L Poor Idle Quality, Surge, Stall VIN: 1G2W314T6N HELP this car is owned by a friend of my mom. car has been at two shops. problem started as stalling, has had intake done twice,second time to verify first, egr valve , and two computers first installed with injectors wire shorted then second to repair first b... Trouble codes: 44 (lean exhast) |
View |
Fixes & Summaries for All Makes and Models
| Fix/Summary | Answers | |
| 1990 Acura Legend 2.7L No Start VIN: JH4KA3246L thanks everyone this solve both problem. fan timer fan run good 30 minutes after shutt off and main relay for hot soak no start.god bless you. |
10 | |
| 2003 Audi A4 3.0L abs module VIN: WAULT68EX3 Sorry it took so long to post the fix. I sent the car back to Audi with the new ABS module installed and they were able to recode it. Thanks for all the help. Fred |
5 | |
| 1995 Dodge Intrepid 3.5L Cuts out, Cruise light flashes VIN: 1B3HD46F5S Well I would say that I have this fixed...3/4 of my replies said crank sensor...It was cheap so I gave it a shot and it took care of it. the other 1/4 od the people said timing belt jumped time..Took a look and found it to be all ok. Thanks to all who replied.... Trouble codes: 55 (all ok). |
15 | |
| 1992 Geo Metro LSi 1.0L Alternator Belt VIN: JG1MR3368N First of all, I'd like to thank all of the people who responded to my inquiery. Aside from the fact that I mistakenly stated that this was a CS144 alternator when in fact it turned out to be a Nippondenso, the overwhelming reponses seemed to lean toward usin... |
24 | |
| 1994 Jeep Grand Cherokee Limited 5.2L No Start, Stall VIN: 1J4GZ78Y2R Sorry for the delay in closing this help request. Here's what has happened. First I want to thank everyone for their help. I followed up on all the leads provided. Everthing on this jeep checked out just fine. Two days ago I got a call from the owner of the je... |
13 | |
| 1991 Mercury Cougar LS 3.8L No Start VIN: 1MEP46043M Sorry, fellas, we got hit pretty hard by hurricane rita so I will not be working on this car for a while. When I do, I will just post a new request and tell y'all what I found! Thanks for all the responses! |
15 | |
| 1988 Pontiac Trans Am GTA 5.7L illustarion Most were very helpful, especially Stan. This request more or less created more questions as to what engine this is. I think with evryones input, I feel comfortable with moving towards installing , what should have been 'stock' roller set up. All that is neede... |
3 |
