 Prev |
Professional Automotive Repair Technical Discussions for June 11, 2004 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1995 Chrysler Cirrus LX 2.5L compressor? VIN: 1C3EJS6H7S Lat summer while on a hot trip vehicle wpould blow high pressure relif valve when at idle for extended times. Chalked it up high heat soak. All the while (after valve closed) air would be cold. This summer no cool, added some R134a, just for band-aid tocheckfo... |
View | |
| 1999 Chrysler Sebring JXi 2.5L No Start VIN: 3C3EL55H6X this car is equiped with a factory anti-theft system and I think this may be causing my no start condition. The car is driven daily on the highway with great maintenance (very well kept)The customer stated that a couple of times it would not start and he would... |
View | |
| 1989 Dodge Dynasty LE 3.0L No Start VIN: 1B3BC5639K car stalled on customer and towed into shop.It will crank over strong but will not start. Acts at times like it flooded but I pulled plugs and they where dry. Checked for spark and have good blue crisp spark. Injectors have power and pulse. No codes, I pulled ... |
View | |
| 1990 Dodge B350 5.2L No Overdrive VIN: 2B7JB31Y2L Hello everyone, I definitely have a tricky one here. I will try to be as descriptive as possible. This vehicle originally went into a transmission shop not moving at all. After rebuilding the transmission, the van was sent to me to diagnose a “no overdrive" co... |
View | |
| 2001 Dodge Stratus SE 2.7L compressor VIN: 1B3EJ46U91 Customer complaint of warm air. Pressures are good, relay and fuses test good, and transducer measured good voltage. If you bypass relay, compressor will engage. A/c will work on defrost and for a very short moment it began to work through vents but quit. Can ... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1995 Chrysler Sebring LXi 2.5L No Overdrive VIN: 4C3AU52N4S FIXED -- OD shift button intermittent open in the wiring, The customer had a friend install a stereo for him he tapped into the wiring for the shift button, We repaired the wiring - Road Tested - OK. Thanks again to iATN and to all who replied. |
3 | |
| 1997 Chrysler Sebring LX 2.5L odometer/rpm VIN: 3C3E255H6V Most of the replies pointed toward the printed circut board. Nobody had any specific test procedures for this. The customer is willing to fix this problem but is going to wait till the next service for the fix. This car is hard to tie up for the day. The day i... |
6 | |
| 1986 Dodge Ram 50 Custom 2.0L electrical VIN: JB7FP24D2G I want to Thank everyone for their help. I renewed the battery cables, which corrected my ground issues and unplugged my pre-cat and it started fine. New cat on way for finish on Monday. I have one question for any one, my ignition fire still faded after the i... |
12 | |
| 1998 Dodge Ram 2500 5.9L No Start VIN: 3B7K52666W I only received 2 replies. Both were relating to fuel. My problem was the energized supply to the fuel relay. Even though the MOD wiring did not show the brown/ white wire going down another harness (it showed it going straight to the ECM), I had exhausted all... Trouble codes: P1689 (No communication between ECM and injection pump module). |
2 | |
| 1991 Jeep Cherokee Laredo 4.0L abs VIN: 1J4FJ58SOM Installed new hcu & actuator Pedal feels fine pumps runs normal (60) seconds |
10 | |
| 1989 Plymouth Acclaim 2.5L flucuation in temp lots of help on this one thank-you. most said either drill 1/8 hole in thermostat or heater core plugged. I the t-stat mod first and it helped. gauge still flucuated but it was much slower. the real fix was back fluch heater core due to the fact that the heate... |
26 | |
| 1990 Plymouth Acclaim 2.5L Engine vacuum loss VIN: 1P3XA46K4L Thanks to everyone that responded, This one was the one way check valve or lack of one seem customers son had replaced the vacuum line from the power booster to the control unit with rubber vacuum hose and did not put back in the check valve. replaced with new... |
14 |
