 Prev |
Professional Automotive Repair Technical Discussions for January 28, 2004 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1995 Dodge Grand Caravan 3.3L heat VIN: 1P4GH44R4S temp comes up to normal operating temp but blows cold when idling, tried everthing, but problem still persists. replace thermostat with dodge, replaced heater core, removed cold hod valve at hoses. |
View | |
| 1999 Dodge Durango SLT 5.2L front differintial VIN: 1B4HS28Y5X This is not my usual type of work so more or less looking for what to look for or is there a typical problem with these front diff. the gear lube is coming out of the vent tube which is very high near the neck of the radiator and the diff. is not over full dri... |
View | |
| 2000 Dodge Grand Caravan ES 3.8L belt VIN: 1B4GP7413Y This is my wifes'vehicle,purchased new.In wet weather the belt has come off at 2 different times when going through water.(small puddles)The belt was replaced & tensioner, though I never thought it was bad & the problem is still there.Another customer with a 2... |
View | |
| 1990 Jeep Wrangler 2.5L Excessive Emissions, No Start, Poor Idle Quality, Stall, Poor Fuel Economy VIN: 2J4FY29E7L Hi Jeep Guys, What we have today is a vehicle that runs real bad. Comperssion, Voltage drops, Powers, Sensors, fuel pressure and pretty much everything I can think of test fine. As you know this is a Renix engine management system, which leaves no codes. My sy... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1987 Chrysler LeBaron 2.5L crank shaft VIN: 3C3CJ41K6H thank you foryour help i was able to pull the engine with out the trans engines in and working fine thanks god bless |
30 | |
| 2002 Chrysler Voyager 2.4L blower resistor VIN: 1C4GJ15B32 this van is fixed and as most of thE replies said the prolem was the blower motor drawing to mucH amps so we installed a new motor and all is fine thanks butch |
12 | |
| 1995 Dodge B2500 5.2L head gaskets VIN: 2B7HB21Y2S Thanks to all that took the time to reply to this fun vehicle,turned out to be a problem with cylnder head surface,the area where the head bolts came thru on combustion chamber side were approx .006 raised from apparent over tightening from factory,apparently ... |
7 | |
| 1995 Dodge Neon 2.0L No Power VIN: 1LAE46SCTS Thanks to all five guys that sent a message back, sorry to say customer never came back to get it fixed. Finally got this new plastic box working so that I could catch up on stuff. Joseph from Dayton Ohio, Dennis from Florida both suggested trying an O2. Bob f... Trouble codes: 21 (Downstream O2 Shorted To VoltageEGR). |
5 | |
| 1996 Dodge Grand Caravan SE 3.3L No Start VIN: 1B4GP44R8T Most replies said to check the flex plate. It was OK. We had a problem with color blindness. Last shop had tested coil and PCM by removing wires in the coil connector. We new this and had checked it with 3 different model year books and one van same year and m... |
10 | |
| 1999 Dodge Ram 2500 5.9L eng.running too cold VIN: 3B7KF26ZOX I received some goood replies stating bad PCM or programming, possible bad temp. sensor. Were are having some normal mid-western winter right now, and with this being a street dept. supervisor's truck&I work a different shift than him I can't get my hands on i... |
4 | |
| 2000 Dodge Ram 1500 Laramie 5.9L govenor pressure VIN: 3B7HF1326Y thanks for all of the replies. most of you hit it right on the nose. replaced the tps and problem solved. thanks a lot. |
15 | |
| 1997 Plymouth Grand Voyager SE 3.0L Fuel odor VIN: 2P4GP4430V All responses were considered and helped us locate the problem. The fuel rail had a small leak next to the support bracket near the hose conection. Thanks to all. |
10 | |
| 1999 Plymouth Voyager 3.0L cylinder heads VIN: 2P4FP2534X thanks to all. after we got the heads off, the machine shop found the exhaust stud threaded areas has hairline cracks. no signs of overtightening of the studs, no overheating or warping. kind of an odd one, we replaced the heads. thanks again to iatn and all o... |
7 |
