 Prev |
Professional Automotive Repair Technical Discussions for October 5, 2022 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for All Makes and Models
| Help Request | Answers | |
| 2015 BMW X5 xDrive35d 3.0L MIL Lamp on VIN: 5UXKS4C56F Car came in with MIL on, DTC: 285A00 - Oxygen sensor after catalytic converter, signal: Short circuit to B+. Bosch part #17021 is listed as the OE part. Either I cannot find this sensor in the exhaust or the Bosch sensor I received is wrong. As far as I ca... |
View | |
| 2011 Cadillac SRX Premium 3.0L Parking Brakes VIN: 3GYFNFEY7B Replaced e brake module due to no communication after replacement and calibration ,still wont operate correctly parking brake light on dash keeps blinking,have power and ground at module and can communicate now but no calibration number in data ,data state... |
View | |
| 2011 Ford F-250 Super Duty Lariat 6.2L Stall VIN: 1FT7W2B64B Tricky one here. Truck will stall out only at idle during warmup. The idle will lower slightly about 3 seconds before and then it apears to loose the fuel injectors and ignition real quick, just enough to stall. Sometimes as it gets warmer it will catch it... |
View | |
| 2013 Ford Escape SEL 2.0L Misfire VIN: 1FMCU9H9XD Hello This vehicle came into the shop with a lack of power. Check engine light on with codes. p0301 misfire cyl 1, p0304 mis cylinder 4 and p0299 TURBOCHARGER/SUPERCHARGER 'A' UNDERBOOST CONDITION. found intake tube full of oil and engine oil leaking from ... Trouble codes: P0299, P0301, P0304 (Misfire cylinder 4) |
View | |
| 1998 GMC K1500 Sierra SL 5.7L Starting VIN: 1GTEK19RXW Truck was towed in for a no crank condition. No power to purple crank wire on starting position. Cranks ok when jumped at relay. Relay has battery power, key off. Has ignition power key on. Has ground. The terminal that goes to starter is showing 6 volts i... |
View | |
| 2003 Infiniti FX45 4.5L air intake t VIN: JNRBS08W03 attn: nissan infinity techs,i cant find an air intake tube for this fx45.part # 16576-cg200. nissan no longer makes it,and i cannot find it online anywhere.anyone know if a tube off another model will work for this.i can see it has a few air chamber boxes ... |
View | |
| 2013 Mini Cooper Countryman S ALL4 1.6L does not accel VIN: WMWZC5C51D LOOKING FOR GOOD KNOWN WAVEFORM ON PIN 5 AND 6 FOR ELECTRONIC THROTTLE BODY ACTUATOR MOTOR. suspecting no control from DME pin 37 to pin 6 on TB. THIS CAR WON'T ACCEL APS checked with scan tool and goes from 0-100% when CT to WOT Throttle angle with key ... |
View | |
| 2009 Volkswagen Routan SEL 4.0L Starting VIN: 2V8HW54X49 Last time in had a new starter but would sometimes delay to crank and other times engage the solenoid and then drop out of the start cycle. We installed another starter and made sure all connections were clean and tight and it didn't act up after that. Cus... |
View |
Fixes & Summaries for All Makes and Models
| Fix/Summary | Answers | |
| 2008 Honda Accord EX 3.5L alarm VIN: 1HGCP36738 hi all,well i think my car is fixed.it does have the factory alarm.i just replaced the driver door pin switch.the pin switch mounted on door post.this style does not have a switch behind the key lock cylinder,so only places it could be is the pin switch or the... |
10 | |
| 2011 Nissan Juke SL 1.6L HVAC Control Head VIN: JN8AF5MV2B After several test drives we did get a compressor cutout and no A/C of course. We also got a second trouble code for a sun load sensor, and we replaced it. We switched compressor relays purely for test purposes. Now the weather has gotten colder here so unable... |
5 | |
| 2014 Nissan Maxima S 3.5L Starter VIN: 1N4AA5AP6E Several good replies about checking for added equipment. Bryan provided some in depth info about how the system works. I agreed with his diagnosis that the BCM was faulty. I did not have the equipment to configure/program a replacement BCM so it was sent to an... |
5 |
