Join Now
International Automotive Technicians Network

P0340 Diagnostic Trouble Code Discussion for May 2013

CMP Sensor Circuit Malfunction


Note: This is a professional automotive technician's resource.
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Trouble Ticket Help Requests for DTC P0340
Help Request Posted
2006 Nissan Sentra S 1.8L MIL Lamp on VIN: 3N1CB51D16
P0340: Camshaft Position Sensor Circuit Malfunction (Bank 1). This car will not start up with first turn of key. On second try it will start and run rough for a few seconds and set a code for camshaft sensor circuit. There is a new camshaft sensor installed . If the code is cleared after it stars and runs it will not set...
May 03, 2013
2007 Ford Focus SE 2.0L MIL Lamp on
P0340: cam sensor circuit. ... have a ford focus with a 2.0 that sets p0340 right when you start the vehicle. the cam sensor has already been replaced. i have checked the two wires between the cam sensor and ecm and they have good contact. i pulled the valve cover and set the cams in ti...
May 08, 2013
2004 Volkswagen Touareg V8 4.2L MIL Lamp on VIN: WVGCM67L74
P0340: camshaft position sensor A circuit bank 1 or single sensor. ... engine light on, and thought for sure I had it. but I was rong it has a code P0340 and the wiring checked good at the conector so i replaced the sensor but the code came back within a minit of running has anyone come accros this and could leed me in the ri...
May 16, 2013
2000 Ford E-350 Econoline 5.4L No Start, Poor Idle Quality, Misfire VIN: 1FDWE35LXY
P0340: Camshaft Position Sensor Circuit Malfunction. Vehicle will not start will just crank and sputter for a second it will run barely on starting fluid. I Thought maybe i had the timing wrong so i reset it and still same problem. Changed fuelpump and filter truck had been sitting for three years apart
May 22, 2013
2000 Ford E-350 Econoline 5.4L No Start, Poor Idle Quality, Misfire VIN: 1FDWE35LXY
P0340: Camshaft Position Sensor Circuit Malfunction. Vehicle will not start will just crank and sputter for a second it will run barely on starting fluid. I Thought maybe i had the timing wrong so i reset it and still same problem. Changed fuelpump and filter truck had been sitting for three years apart
May 24, 2013
2003 Suzuki Aerio SX 2.0L No Start VIN: JS2RC41H63
P0340: Camshaft Position Sensor Circuit Malfunction. Could use some help on a suzuki.Vehicle towed in for no start.Computer had codes 340 and 610.Cleared codes and tried to start.340 resets while cranking.Checked for spark,none,checked for injector pulse,one blink when first start cranking,then none.Followed cha...
May 24, 2013
2003 Suzuki Aerio SX 2.0L No Start VIN: JS2RC41H63
P0340: Camshaft Position Sensor Circuit Malfunction. Could use some help on a suzuki.Vehicle towed in for no start.Computer had codes 340 and 610.Cleared codes and tried to start.340 resets while cranking.Checked for spark,none,checked for injector pulse,one blink when first start cranking,then none.Followed cha...
May 26, 2013
2006 Nissan Sentra S 1.8L MIL Lamp on VIN: 3N1CB51D16
P0340: Camshaft Position Sensor Circuit Malfunction (Bank 1). This car will not start up with first turn of key. On second try it will start and run rough for a few seconds and set a code for camshaft sensor circuit. There is a new camshaft sensor installed . If the code is cleared after it stars and runs it will not set...
May 03, 2013
2007 Ford Focus SE 2.0L MIL Lamp on
P0340: cam sensor circuit. ... have a ford focus with a 2.0 that sets p0340 right when you start the vehicle. the cam sensor has already been replaced. i have checked the two wires between the cam sensor and ecm and they have good contact. i pulled the valve cover and set the cams in ti...
May 08, 2013
2004 Volkswagen Touareg V8 4.2L MIL Lamp on VIN: WVGCM67L74
P0340: camshaft position sensor A circuit bank 1 or single sensor. ... engine light on, and thought for sure I had it. but I was rong it has a code P0340 and the wiring checked good at the conector so i replaced the sensor but the code came back within a minit of running has anyone come accros this and could leed me in the ri...
May 16, 2013
2000 Ford E-350 Econoline 5.4L No Start, Poor Idle Quality, Misfire VIN: 1FDWE35LXY
P0340: Camshaft Position Sensor Circuit Malfunction. Vehicle will not start will just crank and sputter for a second it will run barely on starting fluid. I Thought maybe i had the timing wrong so i reset it and still same problem. Changed fuelpump and filter truck had been sitting for three years apart
May 22, 2013
2000 Ford E-350 Econoline 5.4L No Start, Poor Idle Quality, Misfire VIN: 1FDWE35LXY
P0340: Camshaft Position Sensor Circuit Malfunction. Vehicle will not start will just crank and sputter for a second it will run barely on starting fluid. I Thought maybe i had the timing wrong so i reset it and still same problem. Changed fuelpump and filter truck had been sitting for three years apart
May 24, 2013
2003 Suzuki Aerio SX 2.0L No Start VIN: JS2RC41H63
P0340: Camshaft Position Sensor Circuit Malfunction. Could use some help on a suzuki.Vehicle towed in for no start.Computer had codes 340 and 610.Cleared codes and tried to start.340 resets while cranking.Checked for spark,none,checked for injector pulse,one blink when first start cranking,then none.Followed cha...
May 24, 2013
2003 Suzuki Aerio SX 2.0L No Start VIN: JS2RC41H63
P0340: Camshaft Position Sensor Circuit Malfunction. Could use some help on a suzuki.Vehicle towed in for no start.Computer had codes 340 and 610.Cleared codes and tried to start.340 resets while cranking.Checked for spark,none,checked for injector pulse,one blink when first start cranking,then none.Followed cha...
May 26, 2013