Join Now
International Automotive Technicians Network

P0335 Diagnostic Trouble Code Discussion for November 2010

Crankshaft Position Sensor Circuit Malfunction


Note: This is a professional automotive technician's resource.
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Trouble Ticket Help Requests for DTC P0335
Help Request Posted
2002 Mitsubishi Galant LS 2.4L MIL Lamp on VIN: 4A3AA46G92
P0335: Crankshaft Position Sensor Circuit Malfunction. This car pops these codes after 2 key cycles. The 12 volt, 5 volt and ground are all intact. The cam and crank sensor are within spec while running. 2.5 - 3.02 volts for the cam and 3.8- 4.00 for the crank. The scope shows good wave form. The tone ring on the ...
November 11, 2010
2004 Dodge Ram 1500 Truck SLT 5.7L Poor Idle Quality, Stall, MIL Lamp on VIN: 1D3HA14J19
P0335: Crankshaft Position Sensor Circuit Malfunction. hi all,wondering if anyone out there has run into this before. this ram truck will not stay running. as stated,has codes for both cam and crank sensors,replaced both sensors with no change. truck cam in 3 quarts low on oil and has been 7,000mi. since last oil ...
November 17, 2010
2005 Toyota prado 4.0L MIL Lamp on VIN: JTEBU25J00
P0335: crank sensor. Hello, I have this Prado in my shop from another workshop. I have fitted a new crank shaft sensor and found the EML light is still on. I have scoped the crank and found it reads O.K I think the Toyota vvti systems is not in sync with crankshaft. Any help would...
November 19, 2010
2004 Dodge Ram 1500 Truck SLT 5.7L Poor Idle Quality, Stall, MIL Lamp on VIN: 1D3HA14J19
P0335: Crankshaft Position Sensor Circuit Malfunction. hi all,wondering if anyone out there has run into this before. this ram truck will not stay running. as stated,has codes for both cam and crank sensors,replaced both sensors with no change. truck cam in 3 quarts low on oil and has been 7,000mi. since last oil ...
November 20, 2010
2002 Mitsubishi Galant ES 2.4L MIL Lamp on VIN: 4A3AA46G12
P0335: Crankshaft Position Sensor Circuit Malfunction. ... Inspection with two codes P0335 and P0340 customer stated the motor was replaced by another repair shop and the CEL came on right away the repair shop tried to fix it but failed it was taken to another shop and the timing belt and crank sensor was changed ...
November 24, 2010
2002 Mitsubishi Galant LS 2.4L MIL Lamp on VIN: 4A3AA46G92
P0335: Crankshaft Position Sensor Circuit Malfunction. This car pops these codes after 2 key cycles. The 12 volt, 5 volt and ground are all intact. The cam and crank sensor are within spec while running. 2.5 - 3.02 volts for the cam and 3.8- 4.00 for the crank. The scope shows good wave form. The tone ring on the ...
November 11, 2010
2004 Dodge Ram 1500 Truck SLT 5.7L Poor Idle Quality, Stall, MIL Lamp on VIN: 1D3HA14J19
P0335: Crankshaft Position Sensor Circuit Malfunction. hi all,wondering if anyone out there has run into this before. this ram truck will not stay running. as stated,has codes for both cam and crank sensors,replaced both sensors with no change. truck cam in 3 quarts low on oil and has been 7,000mi. since last oil ...
November 17, 2010
2005 Toyota prado 4.0L MIL Lamp on VIN: JTEBU25J00
P0335: crank sensor. Hello, I have this Prado in my shop from another workshop. I have fitted a new crank shaft sensor and found the EML light is still on. I have scoped the crank and found it reads O.K I think the Toyota vvti systems is not in sync with crankshaft. Any help would...
November 19, 2010
2004 Dodge Ram 1500 Truck SLT 5.7L Poor Idle Quality, Stall, MIL Lamp on VIN: 1D3HA14J19
P0335: Crankshaft Position Sensor Circuit Malfunction. hi all,wondering if anyone out there has run into this before. this ram truck will not stay running. as stated,has codes for both cam and crank sensors,replaced both sensors with no change. truck cam in 3 quarts low on oil and has been 7,000mi. since last oil ...
November 20, 2010
2002 Mitsubishi Galant ES 2.4L MIL Lamp on VIN: 4A3AA46G12
P0335: Crankshaft Position Sensor Circuit Malfunction. ... Inspection with two codes P0335 and P0340 customer stated the motor was replaced by another repair shop and the CEL came on right away the repair shop tried to fix it but failed it was taken to another shop and the timing belt and crank sensor was changed ...
November 24, 2010