P0340 Diagnostic Trouble Code Discussion for May 2009
CMP Sensor Circuit Malfunction
Note: This is a professional automotive technician's resource.
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.Trouble Ticket Help Requests for DTC P0340
| Help Request | Posted | |
| 1996 Toyota Camry DX 2.2L Hesitation, Surge, Cuts out, Stall, MIL Lamp on VIN: 4T1BG12K8T P0340: Camshaft Position Sensor Circuit Malfunction. ... hot or cold -most of the time it will restart and stall again a few times and then will be OK for hours at a time. Car came in on the hook and started OK. I did quick check for anything obvious and found a code p1335 crank sensor circuit. I ohmed it out an... |
May 01, 2009 | |
| 2000 BMW 323i 2.5L MIL Lamp on VIN: WBAAM3338Y P0340: camshaft position sensor inlet. ... check engine light on. code 65 or generic code P0340 camshaft positoin sensor inlet is present car runs great. I check sensor with Vantage pro and it tested ok. good signal not out of range, good frequency. I back brove at sensror and at coputer and sensor... |
May 07, 2009 | |
| 2004 Chrysler Pacifica 3.5L No Start, MIL Lamp on VIN: 2C8GF6848R P0340: Camshaft Position Sensor Circuit Malfunction. hi every one car came from another shop thay say it's a pcm has crank but no start if you clear codes thay come right back just key on without cranking engine. Has anybody heard of a reflash for this problem before. Customer was driving and car just died |
May 07, 2009 | |
| 1999 Nissan Quest GLE 3.3L No Start VIN: 4N2XN11TXX P0340: Camshaft Position Sensor Circuit Malfunction. i am posting this request although i have already fixed it, because it may be beneficial to others. vehicle came in as a no-start. pulled codes for crank sensor, and knock sensor. decided to replace both because of high failure rate. vehicle would run, but had... |
May 07, 2009 | |
| 2000 BMW 323i 2.5L MIL Lamp on VIN: WBAAM3338Y P0340: camshaft position sensor inlet. ... check engine light on. code 65 or generic code P0340 camshaft positoin sensor inlet is present car runs great. I check sensor with Vantage pro and it tested ok. good signal not out of range, good frequency. I back brove at sensror and at coputer and sensor... |
May 12, 2009 | |
| 1998 Volvo V70 2.4L No Start, MIL Lamp on VIN: YV1LW5572W P0340: camshaft position sensor signal. This vehicle was towed in for a no start. There is no spark and the fuel injector pulse blinks twice and then there is none. After clearing the trouble code it comes back right away when cranking the engine. One thing that has me concerned is that there is no ... |
May 13, 2009 | |
| 2000 Ford F-450 Super Duty XL 7.3L No Start, Stall VIN: F123F1X000 P0340: Camshaft Position Sensor Circuit Malfunction. ... ran codes got a po340,p1211,p1212,p1670 so in installed a new CPS sensor cleared codes...still no start. Checked oil - 2 quarts low - added 2 quarts started right up and ran for about 1 minute---then it started running li... |
May 15, 2009 | |
| 2003 Jeep Liberty Renegade 3.7L Poor Idle Quality, Hesitation, Surge, Cuts out, Stall, MIL Lamp on VIN: 1J4HL38K13 P0340: Camshaft Position Sensor Circuit Malfunction. I have a problem with the OEM crank sensor.I had to basically pry the old one out of the block.The new one won't fit in the hole.The old sensor outside diameter is .858 and the new sensor is .863 . I have tryed 2 new OEM sensors so far and no difference.They w... |
May 16, 2009 | |
| 2004 Dodge Caravan SE 3.3L Hesitation VIN: 1D4GP25R74 P0340: No Camshaft Sensor Signals At PCM. ... won't restart. Towed to shop and starts and idles OK. Scanned for codes P0129, P0335, P0340. Erased codes and test drive. Codes did not return in 20 km. Test drove with various stop/starts.... |
May 21, 2009 |
