Trouble Ticket Help Requests for DTC P0340
|1998 Toyota RAV4 2.0L Hesitation, MIL Lamp on VIN: JT3HP10V5W
P0340: Camshaft Position Sensor Circuit Malfunction. ... dohc 2wd stnd trans california emissions... here in the shop... sets a hard code...erase and comes back instantly... p0340 camshaft position sensor circuit malfunction... customer replaced both cam and crank sensors and at the same time replaced the timing...
|August 01, 2007|
|2001 Mercury Sable LS Premium 3.0L Misfire, MIL Lamp on VIN: 1MEFM55S61
P0340: misfire 4 cylinder. hey guys. got this 01 sable with the dohc 3.0. misfires intermittently on # 4 cylinder. ignition system is in good shape as is the engine itself. a scope isn't available to me, so i used a stethoscope to determine that #4 injecter goes away sometimes. i swappe...
|August 03, 2007|
|2001 Chrysler Sebring LXi 3.0L MIL Lamp on VIN: 4C3AG52H31
P0340: No Camshaft Sensor Signals At PCM. Hi guys this one is either going to be real easy or real hard to fix.Our other shop just put in a used engine.Now both the CKP and CMP codes set.you can clear them then drive it and they won't come back.Then shut it off and start it and they are back.I can onl...
|August 06, 2007|
|2003 Ford Ranger XL 3.0L Poor Idle Quality, Cuts out, Stall, MIL Lamp on VIN: 1FTYRTOU13
P0340: cam sensor ckt fault. customer came in with complaint of poor run at high way speeds tested system and found only one fault code for intake air temp sensor out of range stored in memory no light on at that time iat is in the mass air flow sensor replaced map reset adaptives and roa...
|August 07, 2007|
|1997 Dodge Intrepid 3.3L Hesitation, Surge, Cuts out, Stall VIN: 2C3HH46T4V
P0340: No Camshaft Sensor Signals At PCM. ... Originally flipped P1345 cam/crank correlation. Since only P0340 Cam postion sensor. Replaced with aftermarket then was put on to OE parts only. Re/Re with Mopar cam sensor, runs way better but it's been two weeks and yesterd...
|August 08, 2007|
|2003 Jeep Liberty Renegade 3.7L Cam Sensor Location VIN: 1J4GL38K23
P0340: Camshaft Position Sensor Circuit Malfunction. Sorry for such an elementary question but can someone please tell me where the cam sensor is located on this engine? I don't have any information on it in my reference material and I can't seem to locate it on the engine
|August 15, 2007|
|2002 Mitsubishi Montero Limited 3.5L Cuts out, Stall VIN: JA4MW51R42
P0340: Camshaft Position Sensor Circuit Malfunction. hi guys. i have a head scratcher here ( for me at least). this 02 montero limited was running good no problem, the customer brought it in for tune up + timing belt. so we did both at the same time. the problem we are facing now is the truck will stall(pass out...
|August 15, 2007|
|2002 Ford F-350 Super Duty Lariat 7.3L Poor Idle Quality, Stall, Misfire, MIL Lamp on, LIMP MODE VIN: 1FTSW31F52
P0340: Camshaft Position Sensor Circuit Malfunction. codes p0340, p1209, p1210, p1211, p1212-all related to high pressure oil pump. many other codes were present. cleared codes & ran koeo test. p0340, p1210 & p1211 reset. engine would die 3 to 5 seconds into koer test. checked ipc sensor for oil in conne...
|August 16, 2007|
|1997 Ford Ranger Splash 2.3L No Start, Cuts out VIN: 1FTCR10A1V
P0340: cmp sensor or crk fault. This is an occsional intermittant, has to run for some time before problem occurs, problems usually goes away while we are testing for cause. When problem occurs we have no communication with the computer and assoon as problems clears computer communication wi...
|August 19, 2007|
|2003 Mercedes-Benz SLK230 Kompressor 2.3L MIL Lamp on VIN: WDBKK49F23
P0340: Cam sensor. This bad boy came in with these same codes a month ago. I Replace the Cam adjust sensor and wire harness. Clear the code and send the car along its merry way. Came back today with the cust irated. I scan for codes and I listed them below. I cleared the code ca...
|August 20, 2007|
|2004 Mitsubishi Lancer ES 2.0L No Start, MIL Lamp on VIN: JA3AJ26E94
P0340: Camshaft Position Sensor Circuit Malfunction. Hello IATN members, I have a 04 Lancer ES, no start. Codes are PO335 and PO340, cam and crank errors. Replaced both sensors still no start. Checked wiring from sensors to ECM, no problems found. Checked ECM powers, grounds and fuses, all good. Checked timing m...
|August 29, 2007|
|1995 Ford Windstar GL 3.8L Misfire VIN: 2FMDA5147S
P0340: Camshaft position sensor circuit failure. ... because it stalled. Looked it over and found a hole in the oil pan. Pulled the pan and it threw #2 connection rod. Customer gave us the go ahead for a new engine. We put a remanufactured engine in and it started. But there is a dead miss on #5 cyl. and it ...
|August 31, 2007|