Join Now
International Automotive Technicians Network

P0340 Diagnostic Trouble Code Discussion for May 2005

CMP Sensor Circuit Malfunction


Note: This is a professional automotive technician's resource.
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Trouble Ticket Help Requests for DTC P0340
Help Request Posted
1997 Ford Taurus GL 3.0L MIL Lamp on VIN: 1FALP52U5V
P0340: CAM SENSOR Malfunction. ... recheck. came in with intermittent mil light ( code p0340; cmp sensor malfunction) and intermitent miss.( I have not felt the miss yet in 4 visits. I pulled the sensor off the shaft to see if dammage inside had occurred. no damage. I pulled shaft. no play...
May 16, 2005
1995 Nissan Maxima GLE 3.0L No Start VIN: JN1CA21D8S
P0340: cam position sensor. ... against the wall. This Nissan came in with a no start condition less than 4000 miles after a trans rebuild. Customer had at first hard starting, then no starting, but would start when pushed. Scaning resulted in no codes initially. Fuel pressure and inject...
May 17, 2005
1996 Dodge Ram 1500 Truck 5.2L No Start, Stall VIN: 3B7HC13Y4T
P0340: No Camshaft Sensor Signals At PCM. ... with the same code-P0340-cam position sensor and it was not running. A new distributor solved the problem at that time. The problem now is the same code is here again and the vehicle will not start at times. Hot or cold, doesn't seem to matter. After repea...
May 25, 2005
1999 Volvo S80 T6 2.8L Misfire VIN: YV1TS909D6
P0340: bank 1 orsignal sensor. i checked over to see which cylinders were misfiring and found that 1,3, and 4th cylinders were misfiring. i checked for injectors milseconds and it was ok. no faulty injectors. check coils for fire, there was no fire on 1,3,and 4. swich coils around where goo...
May 27, 2005
1997 Ford Taurus GL 3.0L MIL Lamp on VIN: 1FALP52U5V
P0340: CAM SENSOR Malfunction. ... recheck. came in with intermittent mil light ( code p0340; cmp sensor malfunction) and intermitent miss.( I have not felt the miss yet in 4 visits. I pulled the sensor off the shaft to see if dammage inside had occurred. no damage. I pulled shaft. no play...
May 16, 2005
1995 Nissan Maxima GLE 3.0L No Start VIN: JN1CA21D8S
P0340: cam position sensor. ... against the wall. This Nissan came in with a no start condition less than 4000 miles after a trans rebuild. Customer had at first hard starting, then no starting, but would start when pushed. Scaning resulted in no codes initially. Fuel pressure and inject...
May 17, 2005
1996 Dodge Ram 1500 Truck 5.2L No Start, Stall VIN: 3B7HC13Y4T
P0340: No Camshaft Sensor Signals At PCM. ... with the same code-P0340-cam position sensor and it was not running. A new distributor solved the problem at that time. The problem now is the same code is here again and the vehicle will not start at times. Hot or cold, doesn't seem to matter. After repea...
May 25, 2005
1999 Volvo S80 T6 2.8L Misfire VIN: YV1TS909D6
P0340: bank 1 orsignal sensor. i checked over to see which cylinders were misfiring and found that 1,3, and 4th cylinders were misfiring. i checked for injectors milseconds and it was ok. no faulty injectors. check coils for fire, there was no fire on 1,3,and 4. swich coils around where goo...
May 27, 2005